up5k_basic

KO | EN

gitlite — search

#javascript #python #hacktoberfest #react #ai #typescript #llm #go #golang #android #machine-learning #rust #deep-learning #linux

(★ 54)

A small 6502 system with MS BASIC in ROM

up5k_basic 최신버젼 다운로드

최종 버전 다운로드 (.zip)

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

# up5k_basic
A small 6502 system with MS BASIC built in a Lattice UltraPlus FPGA. This system
includes the following features:

* Up to 52kB SRAM with optional write protect (using two of the four available SPRAM cores)
* 8 bits input, 8 bits output
* 115200bps serial I/O port
* NTSC color composite video with text/glyph and graphic modes,
  32kB video RAM (4 8kB pages) and original OSI 2kB character ROM
* 2kB ROM for startup and I/O support
* 8kB Ohio Scientific C1P Microsoft BASIC loaded from spi flash into protected RAM
* SPI port with access to 4MB flash memory
* LED PWM driver
* PS/2 Keyboard port with tx and rx capability
* 4-voice sound generator with 1-bit sigma-delta output

![board](https://raw.githubusercontent.com/emeb/up5k_basic/master/doc/board.png)

## prerequisites
To build this you will need the following FPGA tools

* Icestorm - ice40 FPGA tools
* Yosys - Synthesis
* Nextpnr - Place and Route (version newer than Mar 23 2019 is needed to support IP cores)

Info on these can be found at http://www.clifford.at/icestorm/

You will also need the following 6502 tools to build the startup ROM:

* cc65 6502 C compiler (for default option) https://github.com/cc65/cc65

## Building

git clone https://github.com/emeb/up5k_basic.git
	cd up5k_basic
	git submodule update --init
	cd icestorm
	make

## Loading

I built this system on a custom up5k board and programmed it with a custom
USB->SPI board that I built so you will definitely need to tweak the programming
target of the Makefile in the icestorm directory to match your own hardware.
Note that the 8kB BASIC ROM must now be loaded into the SPI configuration
flash memory starting at offset 0x40000 in order for BASIC to run correctly.
You can find a link to the ROM data at the end of this document.

## Booting up

You will need to connect a PS/2 keyboard to the ps2_clk/dat pins, or a
115200bps serial terminal port to the TX/RX pins of the FPGA - the data input
routines can take characters from either or both. Load the bitstream an you'll
see the boot prompt:

D/C/W/M?

This is asking which initial service to start.

* D - diagnostics. Currently unused, just enters an infinite loop.
* C - Cold start BASIC. This is what you'll normally want.
* W - Warm start BASIC. Use this only after BASIC has been running and the system has been reset.
* M - Machine Language Monitor.

Hit the key of choice (uppercase only!) to continue.

## Running BASIC

After hitting "C", BASIC will initialize. It will prompt you:

MEMORY SIZE?

to which you answer with 'enter' to let it use all memory. It then prompts
with:

TERMINAL WIDTH?

Again, hit 'enter' to use the default. It then prints a welcome message and
is ready to accept BASIC commands and code. You can find out more about
how to use this version of BASIC here: https://www.pcjs.org/docs/c1pjs/

## Enhancements to BASIC

I've upgraded the LOAD and SAVE commands in BASIC from the original bare-bones
features found in the OSI ROMs which were intended for simple audio tape
storage. Now, LOAD/SAVE operate on "slots" of up to 32kB stored in the SPI
Flash memory connected to the FPGA. Use LOAD [n] or SAVE [n] where [n] is an
integer from 0-99 that refers to the memory slot in which you wish to save
or load your BASIC program.

Memory slots contain raw ASCII text of the programs (un-tokenized), so you
could conceivably pre-load the SPI Flash with code from an external source.
Slots start at 0x050000 in the flash memory space and are spaced every 0x8000.
Program text is terminated with 0xFF, so just leave unused bytes in the
default erased state.

The BASIC line input routine has been patched to allow use of the the Backspace
key instead of the underline character. The video text output driver has not
been altered so the cursor doesn't actually back up.

## C'MON Machine Language Monitor

C'MON is a simple hex machine language monitor for the 6502 written by
Bruce Clark and placed in the public domain which allows examining and
editing memory contents as well as executing machine code.

Answering "M" to the boot prompt will print a quick help header and start
the C'MON monitor.

## Boot ROM

The 2kB ROM located at $f800 - $ffff contains the various reset/interrupt
vectors, initialization code, the C'MON monitor and I/O routines needed to
load and support BASIC.

You can revise this ROM with your own additional support code - you may need
to edit the linker script to change the memory sizes. The cc65 assembler and
linker are required to put it all together into the final .hex file needed by
the FPGA build.

## Serial I/O

Originally this project relied on a FOSS USART coded in Verilog that I came
across elsewhere on github. I discovered that there were some issues with it
so it has been replaced with a design that I built myself and which seems to
behave much more reliably while also using fewer resources. The serial I/O
parameters are fixed at 115200bps 8/N/1 but the data rate can be easily
changed over a wide range with simple tweaks to parameters in the acia.v file.

## Video

This is an NTSC color composite video generator which is a significant
improvement over the original OSI Challenger 1P/Superboard II video that
the system started out with. Features are:

* 32x28 text/glyph mode using the OSI 8x8 character generator
* Separate foreground / background colors per-character in text/glyph mode
* 256x224 two-color pixel graphics mode
* 4 8kB memory pages for text or graphics

![characters](https://raw.githubusercontent.com/emeb/up5k_basic/master/doc/chargen1x.png)

The 75 ohm baseband composite video signal is synthesized by means of a 4-bit
weighted-R DAC driven directly by four bits from the FPGA.

![DAC](https://raw.githubusercontent.com/emeb/up5k_basic/master/doc/video_dac.png)

## PS/2 Keyboard

A PS/2 keyboard port is provided which (along with the ACIA) feeds the ASCII
input. Host to keyboard communication is supported and the caps lock LED should
toggle on/off to indicate status.

![PS/2](https://raw.githubusercontent.com/emeb/up5k_basic/master/doc/PS_2.png)

## Reset

An active-low "soft" reset input will reset the 6502 system without reconfiguring
the FPGA. This will return the system the the "D/C/W/M" prompt and allow a warm-
start into BASIC for recovery from some situations.

![Reset](https://raw.githubusercontent.com/emeb/up5k_basic/master/doc/reset.png)

## SPI Flash

The iCE40 Ultra Plus features two SPI and two I2C ports as hard IP cores that
are accessible through a "system bus" that's similar to the popular Wishbone
standard. I've added a 6502 to Wishbone bridge mapped to addresses $F100-$F1FF
which provides access to all four cores. Currently only the SPI core at
addresses $F106-$F10F is connected and it is used to read the BASIC ROM from
flash into SPRAM and support LOAD and SAVE operations.

## LED PWM

Many FPGAs in the iCE40 family provide hard IP cores for driving RGB LEDs. A
simple interface to this is provided so the 6502 may control the LED driver.

## Sound Generator

A 4-voice sound generator is provided which supports pitch from 0-32kHz in 
roughly 0.5Hz steps, choice of waveform (saw/square/triangle/noise) and
volume control on each voice. Output is via a 1-bit sigma-delta process
which requires a simple 1-pole RC filter (100ohm + 0.1uf) lowpass filter
to smooth the digital pulse waveform down to analog audio.

![Audio](https://raw.githubusercontent.com/emeb/up5k_basic/master/doc/audio_filter.png)

## Simulating

Simulation is supported and requires the following prerequisites:

* Icarus Verilog simulator http://iverilog.icarus.com/
* GTKWave waveform viewer http://gtkwave.sourceforge.net/

To simulate, use the following commands

cd icarus
	make
	make wave

This will build the simulation executable, run it and then view the output.

## Copyright

There have been questions raised about the copyright status of the MS BASIC
provided in this project. To the best of my knowledge, the contents of the file
src/basic_8k.hex is still property of Microsoft and is used here for educational
purposes only. The full source code for this can be found at:

https://github.com/brajeshwar/Microsoft-BASIC-for-6502-Original-Source-Code-1978

The ROM files from which I created the .hex file are also available in many
places - I used this archive: http://www.osiweb.org/misc/OSI600_RAM_ROM.zip

## Thanks

Thanks to the developers of all the tools used for this, as well as the authors
of the IP cores I snagged for the 6502 and UART. I've added those as submodules
so you'll know where to get them and who to give credit to.

up5k_basic

up5k_basic 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

up5k_basic

up5k_basic 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

Download README