html-json-speed-comparison

KO | EN

gitlite — search

#javascript #python #hacktoberfest #react #ai #typescript #llm #go #golang #android #machine-learning #rust #deep-learning #linux

html-json-speed-comparison

(★ 12)

Comparing SSR into HTML & JSON in Flask

html-json-speed-comparison 최신버젼 다운로드

최종 버전 다운로드 (.zip)

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

# HTML vs JSON Dynamic Generation Speed Comparison

This is a simple project I set up to compare how long it takes flask to render a response in three different
formats:

* A full HTML page
* A partial HTML page
* A JSON response

In all three cases the page is rendering 1000 contacts.  The two HTML responses use 
[Jinja2](https://jinja.palletsprojects.com/en/2.10.x/) templates.  The JSON end point uses the
[dataclass](https://docs.python.org/3/library/dataclasses.html) library to make JSON serialization of the
sole model, `contacts.py`, easy.

## Data Setup

The data for this test is stored in `contacts.json` and is loaded at server startup so that responses can
be, as much as possible, purely rendering time.

## Client Side

On the client side we run a tight loop of requests to the same end-point over and over again and record
the time it takes to respond.  Since this is against local host there is very low latency, but the network
connection time is obviously still significant.  In real-world latency environments the results would be
even closer to one another, since latency tends to dominate in most distributed systems.

## Caveats

* This is Flask & Python, other platforms might have different characteristics and mechanisms for both HTML & JSON serialization 
* I am not an expert python or flask programmer, this is probably not a great example of python code to follow.
* I intentionally kept things very simple
* I did not do any performance tuning for any of the endpoints
* I may not have chosen the "standard" way to produce JSON, just the easiest
* I am printing the server-side response time which adds CPU to each request
* Returning 1000 contacts is not realistic for most application data display needs

## Results

The results vary of course, but on my machine (Macbook M2) a representative result is as follows:

```
Average Full HTML Time : 7.261ms
Average Partial HTML Time : 7.115ms
Average JSON Time : 12.231ms
```

The full HTML response typically (but not always!) takes the longest, the partial HTML response is usually the
fastest by a bit and the JSON response is typically the slowest.

Looking at the logs on the server side, the response time is almost always sub 10ms (ie undetectably fast), with the 
occasional spike to 15ms.  This seems likely to be garbage collection time, given its inconsistency.

Here are some sample server side response times:

```

4 ms GET /full-html {}
4 ms GET /full-html {}
4 ms GET /full-html {}
4 ms GET /full-html {}
4 ms GET /full-html {}

...

3 ms GET /partial-html {}
2 ms GET /partial-html {}
2 ms GET /partial-html {}
2 ms GET /partial-html {}
3 ms GET /partial-html {}

...

6 ms GET /json {}
6 ms GET /json {}
6 ms GET /json {}
6 ms GET /json {}
6 ms GET /json {}
```

One theory I have on why JSON serialization might
be a _bit_ slower in some cases is that it seems to use reflection, whereas the templates are hard coded.  Also, I would
note that a JSON API often returns all data, regardless of necessity, whereas an HTML API returns the minimum data necessary
for a given UI because, well, it _is_ the UI.

This is speculation, however, and my take-away from all this is **not** that HTML is faster than JSON: I'm sure with a 
well tuned JSON serialization mechanism the JSON responses can be made faster than the HTML responses.  Rather it is that the two approaches are very close 
to one another and are probably round off errors in the overall scheme of total system performance.  Once you hit a data store, or add 
in real-world latency between the client and server, these differences vanish in the wash.

As such, my opinion continues to be that server-side render performance is _not_ a reason to choose either a JSON-based approach
or a hypermedia/HTML based approach to building your web application.  You instead should use other criteria for picking between the two.

I try to outline when I think hypermedia is a good choice in my essay ["When To Use Hypermedia"](https://htmx.org/essays/when-to-use-hypermedia/)

html-json-speed-comparison

html-json-speed-comparison 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

html-json-speed-comparison

html-json-speed-comparison 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

Download README