belt_lock

KO | EN

gitlite — search

#python #hacktoberfest #typescript #go #golang #linux #docker #nodejs #cli #kubernetes #vue #awesome-list #mcp #openai

(★ 10)

A solution for mounting 9mm and 6mm gt2 belts to mgn12 carriage with M2-SHCS or 2mm pin.

belt_lock 최신버젼 다운로드

최종 버전 다운로드 (.zip)

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

# belt_lock
by [MikeYankeeOscarBeta](https://github.com/MikeYankeeOscarBeta/) (VoronDesign Discord: #MikeyMike V2.5796, Voron Toolchangers Discord: MikeyMike - Github: [MikeYankeeOscarBeta](https://github.com/MikeYankeeOscarBeta/StealthChanger))

## Description
A solution for mounting 9mm and 6mm 2mgt/2gt GT2/GT3 belts to mgn12 carriage with M2-SHCS or 2mm pin. Designed to handle high belt tensions.
Versions for both inverted and normal belts.

## Features
- Belt Pin
- Does not clamp the belt against the carriage, carriage-wipers or anything other than itself
- For monolith (inverted belts) it will not change the belt path (keeps the belt path perfectly straight)
- For normal belt direction there will be a ~0.8mm y offset
- Keeps within the confines of the carriage (unless using the external clamps)
- builds just 6mm out in y
- Tested with 15kg static load per belt

## BOM
| Part                        | Amount    | Description                                                                      |
|-----------------------------|-----------|----------------------------------------------------------------------------------|
| M2x25mm SHCS or 2x25mm PIN  | 4         |  Pin leaves more material, hence stronger.                                       |
|                             |           |  M2 SHCS for ease of use                                                         |
|                             |           |  (only 2 screws if using single pin and clamp version (shuttle_clamper_body_v75) |

## Print Instructions
- Print it upright, the strength comes from the layer direction. printing it in the incorrect orientation will result in a weaker part.  
- Use support (make sure your supports are tuned to the point where you're able to remove them carefully without breaking the part).  
- 40%+ infill  
- 4 perimitters  
- 4 top and bottom layers  
- 0.2mm layer height  (or smaller)
- 0.4mm nozzle (or smaller)
- enable filling gaps

## Part Instructions
### shuttle_clamper_body_v101_inverted_belt_gt2_epdm
main body, for no loss in x.
For inverted belts in EPDM (LL-GT2 E) and GT3. will be too loose for normal GT2 (rubber) belts.
Should work with GT2 RF (rubber/normal) belts as well, but will slip sooner (<15kg)

### shuttle_clamper_body_v96_*
main body, for no loss in x.
For inverted belts gt2 rubber belts (LL-2GT RF). Too tight for GT2 EPDM or GT3.

### shuttle_clamper_body_v96_normal_belt
For normal (non-inverted) GT2-R (rubber) belts.

### shuttle_clamper_body_v75
Single pin, no teardrop lock. For both normal and inverted belts. GT2 rubber and epdm, and GT3.
Requires use with a clamp like m2_belt_clamp or m3_BeefyBeltClamp.

### m2_belt_clamp
small footprint belt clamp using m2 screws and heatset nuts.

### m3_BeefyBeltClamp
Beefy clamp using m3 screws and hexnuts.

### BOM - m2_belt_clamp
| Part                        | Amount    | Description                                                      |
|-----------------------------|-----------|------------------------------------------------------------------|
| m2x4x3.5 Heatset Nut         | 6        |  4mm deep, m2 threads, 3.5mm outer diameter                      |
| m2x10mm SHCS Screw           | 6        |  m2x12 SHCS also works ok                                        |

### BOM - m3_BeefyBeltClamp
| Part                        | Amount    | Description                                                      |
|-----------------------------|-----------|------------------------------------------------------------------|
| m3 hexnut                   | 6        |                                                                   |
| m3x8mm SHCS Screw           | 6        | m3x12 SHCS also works                                             |

## Support
Raise issues via github or contact via discord.
Voron Toolchangers Discord "Belt Lock" thread: https://discord.com/channels/1119433664799965186/1218280403870289990

belt_lock

belt_lock 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

belt_lock

belt_lock 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

Download README