bme68x-python-library

KO | EN

gitlite — search

#javascript #python #hacktoberfest #react #ai #typescript #llm #go #golang #android #machine-learning #rust #deep-learning #linux

bme68x-python-library

(★ 52)

Python 3 Library for BME688 and BME680 (Bosch Sensortec sensors), supports Bosch BSEC

bme68x-python-library Latest Version Download

Download Latest Version (.zip)

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

# BME68X and BSEC2.0 for Python by pi3g

This Python extension enables you to read measurement data by the BME68X sensor and the BSEC2.0 library from BOSCH. 
The BME68X sensors by BOSCH Sensortec measure temperature, pressure and humidity. 
Most importantly the sensor estimates the air pollution by recording the amount of VOCs (Volatile Organic Compounds). 
With use of the (licensed) BSEC library from BOSCH, this allows for measuring the IAQ (Indoor Air Quality).

**Check out this [Installation Video](https://www.youtube.com/watch?v=TGWKcCPKhIE&t=12s)!**

### How to install the extension without BSEC
```bash
pip3 install bme68x
```

### How to install the extension with BSEC
- clone [this repo](https://github.com/pi3g/bme68x-python-library) to a desired location on you hard drive
- download the licensed BSEC2.0 library [from BOSCH](https://www.bosch-sensortec.com/software-tools/software/bme688-software/) 
- unzip it into the *bme68x-python-library-main* folder, next to this *README.md*
- open a new terminal window inside the *bme68x-python-library-main* folder
```bash
sudo python3 setup.py install
```
or to install under venv use
```bash
path/to/venv/bin/python3 setup.py install
```
### How to use the extension
- to import in Python
```python
import bme68x
```
or
```python
from bme68x import BME68X
```
- see PythonDocumentation.md for reference
- to test the installation make sure you connected your BME68X sensor via I2C
- run the following code in a Python3 interpreter
```python
from bme68x import BME68X

# Replace I2C_ADDR with the I2C address of your sensor
# Either 0x76 (default for BME680) or 0x77 (default for BME688)
bme68x = BME68X(I2C_ADDR, 0)
bme68x.set_heatr_conf(1, 320, 100, 1)
data = bme68x.get_data()
```

#### For documentation and examples please refer to our [GitHub](https://github.com/pi3g/bme68x-python-library) 
#### For feedback, bug reports or functionality requests send an E-mail to nathan@pi3g.com

![pi3g logo](https://pi3g.com/wp-content/uploads/2015/06/pi3g-150px-only-transparent-e1622110450400.png) 
pi3g is an official approved Raspberry Pi reseller, and a Coral Machine Learning Platform (from Google) distribution partner. 
We take care of all your Raspberry Pi and Coral related hardware and software development, sourcing, accessory and consulting needs! 
Check out [our homepage](https://pi3g.com) and file your personal software or hardware request. 
Also visit [our shop](https://buyzero.de).

bme68x-python-library

bme68x-python-library Latest Version Download

Today's picks

Was this content helpful?

Recent Feedback

bme68x-python-library

bme68x-python-library Latest Version Download

Today's picks

Was this content helpful?

Recent Feedback

Download README