MCP23017_RT

KO | EN

gitlite — search

#hacktoberfest #react #typescript #llm #rust #docker #nodejs #java #kubernetes #awesome-list #security #mcp #openai #open-source

(★ 31)

Arduino library for I2C MCP23017 16 channel port expander

MCP23017_RT 최신버젼 다운로드

최종 버전 다운로드 (.zip)

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

[![Arduino CI](https://github.com/RobTillaart/MCP23017_RT/workflows/Arduino%20CI/badge.svg)](https://github.com/marketplace/actions/arduino_ci)
[![Arduino-lint](https://github.com/RobTillaart/MCP23017_RT/actions/workflows/arduino-lint.yml/badge.svg)](https://github.com/RobTillaart/MCP23017_RT/actions/workflows/arduino-lint.yml)
[![JSON check](https://github.com/RobTillaart/MCP23017_RT/actions/workflows/jsoncheck.yml/badge.svg)](https://github.com/RobTillaart/MCP23017_RT/actions/workflows/jsoncheck.yml)
[![GitHub issues](https://img.shields.io/github/issues/RobTillaart/MCP23017_RT.svg)](https://github.com/RobTillaart/MCP23017_RT/issues)

[![License: MIT](https://img.shields.io/badge/license-MIT-green.svg)](https://github.com/RobTillaart/MCP23017_RT/blob/master/LICENSE)
[![GitHub release](https://img.shields.io/github/release/RobTillaart/MCP23017_RT.svg?maxAge=3600)](https://github.com/RobTillaart/MCP23017_RT/releases)
[![PlatformIO Registry](https://badges.registry.platformio.org/packages/robtillaart/library/MCP23017.svg)](https://registry.platformio.org/libraries/robtillaart/MCP23017)

# MCP23017_RT

Arduino library for MCP23017 16 channel I2C port expander.

## Description

This library gives easy control over the 16 pins of a (I2C) MCP23017 chip.

This IC is strongly related to the MCP23S17 SPI port expander - https://github.com/RobTillaart/MCP23S17
Programming Interface is kept the same as much as possible.

The **write1(pin, value)** is optimized. 
If a pin is not changed it will not be written again to save time.

Feedback as always is welcome.

### REV D - June 2022

The I2C IO expander MCP23017 has changed according to the new data sheet. 
It is now described as a 14/16-bit IO expander.
The pins **GPA7** (7) and **GPB7** (15) have lost their input mode, output mode still works.
The chips look the same and did not change names.
This implies it not possible to read 8 bits in parallel at the exact same moment if you have a REV D die.
The REV D version now need reading both A and B register to get 8 bits parallel (with a minor delay).

Some details see:

- https://hackaday.com/2023/02/03/mcp23017-went-through-shortage-hell-lost-two-inputs/
- https://ww1.microchip.com/downloads/aemDocuments/documents/APID/ProductDocuments/DataSheets/MCP23017-Data-Sheet-DS20001952.pdf
- https://microchip.my.site.com/s/article/GPA7---GPB7-Cannot-Be-Used-as-Inputs-In-MCP23017
- https://www.elektormagazine.com/articles/breakout-board-mcp23017  (comment)
- https://forums.raspberrypi.com/viewtopic.php?t=91209&sid=f8c6df7c8ede76937a66503edfe25394
- https://github.com/RobTillaart/MCP23017_RT/issues/40  (some notes).

Note: the library has no provisions (yet) for detecting DEV D chips or handle them in a special way.
There is an idea to implement a derived class MCP23017_REVD that provides automatic support.
However no priority.

Note that the MCP23S017 (SPI version) does not have this "feature" for **GPA7** and **GPB7**.

## 0.9.0  Breaking change

Fix #44, **reverse16ByteOrder(bool)** is added to reverse the byte order of the 16 bit API.
Not using or setting the parameter to false keeps the library backwards compatible.

### 0.8.0 Breaking change

Fix for #47 MCP23S17, bug in enable interrupt handling.
Pre 0.8.0 versions are obsolete.

### 0.6.0 Breaking change

The version 0.6.0 has breaking changes in the interface. 
The rationale is that the programming environment of the **Arduino ESP32 S3** 
board uses a remapping by means of the include file **io_pin_remap.h**.
This file remaps the pins of several core Arduino functions. 
The remapping is implemented by #define macros and these implement "hard" text 
replacements without considering context. 
The effect is that methods from this class (and several others) which have the same 
name as those Arduino core functions will be remapped into something not working.

The following library functions have been renamed:

|  old name        |  new name    |  notes  |
|:-----------------|:-------------|:--------|
|  analogRead()    |  read()      |
|  analogWrite()   |  write()     |
|  pinMode()       |  pinMode1()  |
|  digitalRead()   |  read1()     |
|  digitalWrite()  |  write1()    |

### 0.5.0 Breaking change

Version 0.5.0 introduced a breaking change.
You cannot set the pins in **begin()** any more.
This reduces the dependency of processor dependent Wire implementations.
The user has to call **Wire.begin()** and can optionally set the Wire pins 
before calling **begin()**.

### I2C

Supports 100kHz, 400kHz and 1.7MHz

TODO - add performance data

###  I2C address

0 = GND
1 = Vcc

|  address  |  A2  |  A1  |  A0  |  notes  |
|:----------|:----:|:----:|:----:|:-------:|
|    0x20   |   0  |   0  |   0  |
|    0x21   |   0  |   0  |   1  |
|    0x22   |   0  |   1  |   0  |
|    0x23   |   0  |   1  |   1  |
|    0x24   |   1  |   0  |   0  |
|    0x25   |   1  |   0  |   1  |
|    0x26   |   1  |   1  |   0  |
|    0x27   |   1  |   1  |   1  |

### I2C multiplexing

Sometimes you need to control more devices than possible with the default
address range the device provides.
This is possible with an I2C multiplexer e.g. TCA9548 which creates up
to eight channels (think of it as I2C subnets) which can use the complete
address range of the device.

Drawback of using a multiplexer is that it takes more administration in
your code e.g. which device is on which channel.
This will slow down the access, which must be taken into account when
deciding which devices are on which channel.
Also note that switching between channels will slow down other devices
too if they are behind the multiplexer.

- https://github.com/RobTillaart/TCA9548

### Related

16 bit port expanders

- https://github.com/RobTillaart/MCP23017_RT  I2C 16 IO lines.
- https://github.com/RobTillaart/MCP23S17  SPI 16 IO lines.
- https://github.com/RobTillaart/PCF8575  I2C 16 IO lines.
- https://github.com/RobTillaart/PCA9671  I2C 16 IO lines. - successor PCF8575
- https://github.com/RobTillaart/TCA9555  I2C 16 IO lines.

8 bit port expanders

- https://github.com/RobTillaart/MCP23008  I2C 8 IO lines.
- https://github.com/RobTillaart/MCP23S08  SPI 8 IO lines.
- https://github.com/RobTillaart/PCF8574  I2C 8 IO lines.
- https://github.com/RobTillaart/TCA9554  I2C 8 IO lines.

Keypad

- https://github.com/AndreKlang/mcp23017-4x4-keypad

## Interface

```cpp
#include "MCP23017.h"
```

### Constructor

- **MCP23017(uint8_t address, TwoWire \*wire = &Wire)** constructor, with default Wire interface.  
Can be overruled with Wire0..WireN.
- **bool begin(bool pullup = true)** initializes library, returns true if successful. 
Default sets the pins to INPUT PULLUP.
Returns false if not connected or a register could not be set.
- **bool isConnected()** returns true if connected, false otherwise.
- **uint8_t getAddress()** returns the address set in the constructor.

Patch for #46
- **void setAddress(uint8_t address)** overrule the set address runtime.
- **void setWire(TwoWire \*wire)** overrule the set I2C bus runtime.

### Single pin interface

Please note REVD remarks at top.

- **bool pinMode1(uint8_t pin, uint8_t mode)** pin = 0..15, mode = INPUT, OUTPUT or INPUT_PULLUP. 
Do NOT use 0, 1 for mode as the 3 constants are (possibly) defined differently.
Returns true if successful.
- **bool write1(uint8_t pin, uint8_t value)** pin = 0..15, value = LOW(0) HIGH (!0). Returns true if successful.
- **uint8_t read1(uint8_t pin)** pin = 0..15, returns LOW or HIGH, might set the lastError();
- **bool setPolarity(uint8_t pin, bool reversed)** pin = 0..15, set reversed flag. Returns true if successful.
- **bool getPolarity(uint8_t pin, bool &reversed)** pin = 0..15, reads reversed flag. Returns true if successful.
- **bool setPullup(uint8_t pin, bool pullup)** pin = 0..15, set pull-up flag. Returns true if successful.
- **bool getPullup(uint8_t pin, bool &pullup)** pin = 0..15, reads pull-up flag. Returns true if successful.

### 8 pins interface

Please note REVD remarks at top.

- **bool pinMode8(uint8_t port, uint8_t mask)** port = 0..1, mask = 0..255. Returns true if successful.
- **bool write8(uint8_t port, uint8_t value)** port = 0..1, value = 0..255. Returns true if successful.
- **uint8_t read8(uint8_t port)** port = 0..1, reads 8 pins into one byte.
- **bool setPolarity8(uint8_t port, uint8_t mask)** port = 0..1, sets polarity for 8 channels at once.
Returns true if successful.
- **bool getPolarity8(uint8_t port, uint8_t &mask)** port = 0..1, reads polarity of 8 channels at once.
Returns true if successful.
- **bool setPullup8(uint8_t port, uint8_t mask)** port = 0..1, sets pull-up for 8 channels at once.
Returns true if successful.
- **bool getPullup8(uint8_t port, uint8_t &mask)** port = 0..1, reads pull-up for 8 channels at once.
Returns true if successful.

### 16 pins interface

Please note REVD remarks at top.

Note: since version 0.9.0 a function is added to reverse the byte order of the 16 bit API.

- **void reverse16ByteOrder(bool reverse = false)** reverse the byte order of the 16 bit API.
Not using this function or setting the parameter to false keeps the library backwards compatible.

- **bool pinMode16(uint16_t mask)** mask = 0..0xFFFF, returns true if successful.
- **bool write16(uint16_t value)** value = 0..0xFFFF, returns true if successful.
- **uint16_t read16()** reads 16 pins into an uint16_t.
- **bool setPolarity16(uint16_t mask)** sets polarity for 16 channels.
Returns true if successful.
- **bool getPolarity16(uint16_t &mask)** reads polarity of 16 channels.
Returns true if successful.
- **bool setPullup16(uint16_t mask)** sets pull-up for 16 channels.
Returns true if successful.
- **bool getPullup16(uint16_t &mask)** reads pull-up for 16 channels.
Returns true if successful.

The reading and writing to registers have been performance optimized for the 16 bit interface.
If there are problems please open an issue.

### Interrupts (experimental 0.6.3)

Read the datasheet for the details, page 24,25.

pin = 0..15  
mode = { RISING, FALLING, CHANGE }  
- **bool enableInterrupt(uint8_t pin, uint8_t mode)** 
Returns true if successful.
Returns MCP23017_PIN_ERROR if pin > 15.
- **bool disableInterrupt(uint8_t pin)**
Returns true if successful.
Returns MCP23017_PIN_ERROR if pin > 15.

8 pin interface, overrides all earlier settings. 
Sets all pins to the same interrupt mode { RISING, FALLING, CHANGE }.  
port = 0, 1  
mask = 0x00..0xFF.
- **bool enableInterrupt8(uint8_t port, uint8_t mask, uint8_t mode)**
- **bool disableInterrupt8(uint8_t port, uint8_t mask)**

16 pin interface, overrides all earlier settings. 
Sets all pins to the same interrupt mode { RISING, FALLING, CHANGE }.
mask = 0x0000..0xFFFF.
- **bool enableInterrupt16(uint16_t mask, uint8_t mode)**
- **bool disableInterrupt16(uint16_t mask)**

Determine which pins caused the Interrupt. (datasheet).
- **uint16_t getInterruptFlagRegister()** Reads all 16 pins.
- **uint8_t getInterruptFlagRegister8()** Reads 8 pins of port. Port == 0, 1
- **uint16_t getInterruptCaptureRegister()** Reads all 16 pins.
Is used to detect if multiple pins triggered an interrupt.
- **uint8_t getInterruptCaptureRegister8(uint8_t port)** reads 8 pins of port.
Port == 0, 1

- **bool setInterruptPolarity(uint8_t polarity)** polarity: 0 = LOW, 1 = HIGH, 2 = NONE/ODR
- **uint8_t getInterruptPolarity()** return set value.

Merge INTA and INTB into one signal so only one line handles all interrupts.
This reduces the number of interrupt lines to handle, however one has 
to read more registers to find the changed ones.

- **bool mirrorInterrupts(bool on)** enables / disables mirror mode.
- **bool isMirroredInterrupts()** returns set option (0,1 or 2).

### IO Control Register

The library supports setting bit fields in the IO control register.
Read the datasheet carefully!

- **bool enableControlRegister(uint8_t mask)** set IOCR bit fields
- **bool disableControlRegister(uint8_t mask)** clear IOCR bit fields

|  constant              |  mask  |  description  |
|:-----------------------|:------:|:--------------|
|  MCP23x17_IOCR_BANK    |  0x80  |  Controls how the registers are addressed.
|  MCP23x17_IOCR_MIRROR  |  0x40  |  INT Pins Mirror bit.
|  MCP23x17_IOCR_SEQOP   |  0x20  |  Sequential Operation mode bit.
|  MCP23x17_IOCR_DISSLW  |  0x10  |  Slew Rate control bit for SDA output.
|  MCP23x17_IOCR_HAEN    |  0x08  |  Hardware Address Enable bit (MCP23S17 only).
|  MCP23x17_IOCR_ODR     |  0x04  |  Configures the INT pin as an open-drain output.
|  MCP23x17_IOCR_INTPOL  |  0x02  |  This bit sets the polarity of the INT output pin.
|  MCP23x17_IOCR_NI      |  0x01  |  Not implemented.

### Error codes

If one of the above functions return false, there might be an error.

- **int lastError()** Above functions set an error flag that can be read with this function.  
Reading it will reset the flag to **MCP23017_OK**.

|  name                     |  value  |  description  |
|:--------------------------|:-------:|:--------------|
|  MCP23017_OK              |  0x00   |  No error     |
|  MCP23017_PIN_ERROR       |  0x81   |
|  MCP23017_I2C_ERROR       |  0x82   |  (compatibility)
|  MCP23017_VALUE_ERROR     |  0x83   |
|  MCP23017_PORT_ERROR      |  0x84   |
|  MCP23017_REGISTER_ERROR  |  0xFF   |  low level.
|  MCP23017_INVALID_READ    |  0xFF   |  low level.

## Future

#### Must

- Improve and extend documentation

#### Should

- keep functional in sync
  - sync error codes to MCP23x17
- buy additional hardware
- test with multiple devices.
  - multi SELECT lines
- add example with interrupts
  - test
  - extend error codes
- add examples
  - rotary decoder
  - IO debounce buttons
- optimize code - squeeze footprint
- add **MCP23x17_INT_MODE_ERROR** - enableInterrupt()

#### Could

- check need for writing in all functions (Polarity / Pull-up)
  - check if bit mask changes.
  - what is performance gain vs footprint?
- investigate and reimplement the INPUT_PULLUP for pinMode() ?
- initial value (16 bit?) as begin parameter (breaking change)
  - depends on input output pull-up etc.
- **getPinMode(), getPinMode8(), getPinMode16()**

#### Wont

- investigate if REV D chips can be detected.
- create a derived class **MCP23017_REVD** => see issue #40

## Support

If you appreciate my libraries, you can support the development and maintenance.
Improve the quality of the libraries by providing issues and Pull Requests, or
donate through PayPal or GitHub sponsors.

Thank you,

MCP23017_RT

MCP23017_RT 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

MCP23017_RT

MCP23017_RT 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

Download README