neotrellis-grid-FTDI-for-monome-devices

KO | EN

gitlite — search

#javascript #python #hacktoberfest #react #ai #typescript #llm #go #golang #android #machine-learning #rust #deep-learning #linux

neotrellis-grid-FTDI-for-monome-devices

(★ 8)

neotrellis grid modification with color palette and baud rate selector for use with norns, teletype, ansible, and other monome eco-system devices

neotrellis-grid-FTDI-for-monome-devices 최신버젼 다운로드

최종 버전 다운로드 (.zip)

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

# neotrellis_teensy_FTDI
neotrellis grid modification with intensity, color palette, and baud rate selector for use with norns, teletype, ansible, and other monome eco-system devices.

![20210321_105515](https://user-images.githubusercontent.com/2180300/111915689-c2703c80-8a34-11eb-8a7a-a64c673d4788.jpg)

This repository outlines how to modify a neotrellis grid that you have built following instructions from https://github.com/okyeron/neotrellis-monome

You will need to set up an FTDI board as described by https://github.com/mcleinn/neotrellis-monome-for-teletype-via-ftdi  I basically followed his instructions, but found that a huge amount of tweaking / sequencing of events was required to select the appropriate baud rate and get all devices to recognize the grid.  At this point, norns is a little finicky - I find that I have to initialize the grid while connected to my norns shield, then reset the norns to get it to be recognized.  A minor inconvenience that might be fixed in the future.

I made a slot next to the Teensy3.2 for the adafruit FTDI friend, and they fit adequately.  Instructions and pictures below.  Once you set up the FTDI and connect it as shown you might want to flash the Teensy with the code in this repository and try it out prior to taking a dremel tool or file to your enclosure.  I did all my debugging with the FTDI hanging outside the enclosure and didn't burn anything out.

Perhaps one day in the future all monome devices will be able to connect directly to a USB Teensy - some generous capable coders have started this endeavor.  This would obviate the FTDI sub-board.  However, when this day comes the FTDI board and old-school mini-USB connecter are a great way to provide more power to the Teensy than the Teensy allows - replacing the sub-board Steven Noreyko added to the original units.  It should be trivial to switch back to Teensy-only operation and use the FTDI for power only at that point.

Modifying the enclosure and shoehorning in the FTDI isn't too hard.  Start by carefully clipping off the FTDI-friend pin header.

![20210307_104949](https://user-images.githubusercontent.com/2180300/111909092-2127bd00-8a19-11eb-86d9-98523c6f51f2.jpg)

De-solder all pins except the two that we won't use - these are to hold the board in place with a couple of small holes much as those that hold the Teensy in place

![20210307_105010](https://user-images.githubusercontent.com/2180300/111909095-2258ea00-8a19-11eb-92a9-3b828d4f17b9.jpg)

Bend the two pin remnants up as shown

![20210307_105742](https://user-images.githubusercontent.com/2180300/111909099-24bb4400-8a19-11eb-84fa-01a27418c6b6.jpg)

Notch the case to provide space for the main chip and components - I used a dremel tool that looks like a drill bit - maybe a cutting wheel would work better?  Drill holes that match the two remaining mounting-pins.  I got these wrong the first time, and found that holding the board where it would go and moving side to side and forwards and backwards scratched the pin positions into the surface enough for me to drill them in the right place.

![20210307_114154](https://user-images.githubusercontent.com/2180300/111909103-271d9e00-8a19-11eb-9c63-844fbb061c08.jpg)

Solder short jumper wires as shown - there isn't much room for these, so keep them short like this.  They will provide space between the board and components beneath it - you could put some electrical tape on the bottom of the board too if you're worried about shorting things together, but I haven't had a problem with that (yet).

![20210307_114742](https://user-images.githubusercontent.com/2180300/111909104-284ecb00-8a19-11eb-9842-43a411320ed8.jpg)
![20210307_115118](https://user-images.githubusercontent.com/2180300/111915869-8a1d2e00-8a35-11eb-8e0c-dca0a194c069.jpg)

Put the case back together.

![20210307_115556](https://user-images.githubusercontent.com/2180300/111909113-2b49bb80-8a19-11eb-8512-58ec77bb3722.jpg)

I will probably drop some screws and spacers on either side of the boards to keep the grid case from bowing this much.

# Using the code
The grid boots up to a device/palette/intensity selector screen.  Lower left corner selects device - if the intensity selection lights (leftmost column) are yellow, the baud rate is set for teletype/Ansible/others.  Press the lower left to toggle that column to white for norns.  Press one of the yellow/white buttons to make the grid brighter / dimmer overall.  Then press button anywhere within a color palette row to choose a color scheme, and the grid should wake up and speak with your monome hardware.  You might need to reset the norns-shield to get it recognized.

At any time, press the three lower right hand corner buttons and release to return to this menu.

I used an eyedropper program to get RGB values from these palettes: https://matplotlib.org/tutorials/colors/colormaps.html  If someone points me at a palette they prefer for color-blindness or sight issues, I'd be happy to add it.

neotrellis-grid-FTDI-for-monome-devices

neotrellis-grid-FTDI-for-monome-devices 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

neotrellis-grid-FTDI-for-monome-devices

neotrellis-grid-FTDI-for-monome-devices 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

Download README