esp32-can-iot

KO | EN

gitlite — search

#python #hacktoberfest #javascript #android #nodejs #csharp #typescript #ios #python3 #django #aws #docker

★ 49 Open GitHub ↗

A ESP32 based interface between CAN-bus and IoT environments.

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

# ESP CAN-Analyzer
An ESP32 based interface between CAN-Bus and IoT environments.

This project has the main objective of interfacing a CAN Bus with the user through the use of the Lawicel Protocol (also known as SLCAN). Lawicel represents CAN Frames as strings of ASCII Symbols which can be easily interpreted by the user of by the numerous applications available online.

![Use_Environment](https://raw.githubusercontent.com/NewTec-GmbH/esp32-can-iot/master/Coding/fw/doc/Media/Use_Environment.png)

- [Technical Specifications](#Technical-Specifications)
	- [Software Requirements](#Software-Requirements)
	- [Hardware Requirements](#Hardware-Requirements)
	- [Extra/Optional Requirements](#Extra/Optional-Requirements)
- [Context](#Context)
- [Use Case](#Use-Case)
- [Potential Optimization](#Potential-Optimization)
- [Specialized Pages](#Specialized-Pages)

# Technical Specifications 
## Software Requirements
* Support Standard and Extended frame formats
* WiFi Mode Selection (AP or STA)
* Support *Lawicel* Protocol
* HTTP Server over WiFi
* Server shall support authentication
* AP credentials changed through Server
* STA credentials changed through Server
* Bit Timing and Filters changed through Server
* CAN monitoring page (depending on available memory)
* Send CAN frame on demand
* Send CAN frame periodically
* CAN BUS Termination on Demand

## Hardware Requirements
* ESP32-based
* ISO 11898 Compliant (CAN up to 1 Mbps)
* CAN Bus Termination on Demand
* Support CAN through DSUB-9
* Support OBD through DSUB-9
* Bus-off State
* ISO 7637 compliant (Road vehicles -- Electrical disturbances from conduction and coupling)
* Control Button
* Red Error LED
* 4 GPIOs via Clamps

## Extra/Optional Requirements
* Identification of Error Message
* Reset through Webserver (Save and Restart)
* View OBD Messages (.dbc file?)
* LAWICEL over websocket/mqtt (to nodejs/node-red)

# Context
![DataFlow](https://raw.githubusercontent.com/NewTec-GmbH/esp32-can-iot/master/Coding/fw/doc/Media/DataFlow.png)

Based on the Lawicel Protocol, this project connects any standard CAN Bus to the user-end system. One example is its use on the Automotive Environment, where the CAN Bus is acquired through the DSUB-9 connector. The Frames are parsed through Lawicel into an ASCII String and sent through Serial to the Users Laptop. There is a second option, which is sending this String through a Websocket to the user. This enables the use of other IoT tools on the user's side, for example, Node-Red.

# Use Case
![UseCaseAnalyzer](http://www.plantuml.com/plantuml/proxy?cache=no&src=https://raw.githubusercontent.com/NewTec-GmbH/esp32-can-iot/master/Coding/fw/doc/design/UseCaseAnalyzer.plantuml)

The use case for this project is based on the direct connection to a CAN Bus, in order to obtain the information being sent between the members of this bus. On the other side of this communication we find a Serial Interface or a Websocket Interface which presents the information to the user. The user has to provide the device with the characteristics of the Bus it is connected to, in order to correctly acquire the data.

# Potential Optimization

Thisproject has the potential to be improved in many of its aspects, specially its Firmware. These are some of the points that have been noted during the development, which can be improved in order to increase the performance:

* Lawicel commands active during AP Mode
* Use of Binary Lawicel Commands instead of Strings
* Optimize the Websocket Buffering of Messages (in both directions)
* Use of both Cores for Tasking
* Send Cyclic Frames using a Lawicel Command
* Prevent reset after car's start/stop

# Specialized Pages

* [Hardware](./Hardware/README.md)
* [Firmware](./Coding/fw/README.md)
	* [Documentation](./Coding/fw/doc/README.md)
	* [Libraries](./Coding/fw/lib/README.md)
		* [Lawicel Protocol](./Coding/fw/lib/Lawicel/README.md)
		* [CAN](./Coding/fw/lib/CAN/README.md)
	* [Application](./Coding/fw/src/README.md)
	* [Unit Test](./Coding/fw/test/README.md)
* [Glosary](./Coding/fw/doc/Glosary.md)

esp32-can-iot

Explore Similar Repositories

Was this content helpful?

Recent Feedback

Download README