Adafruit_nRF51822_Flasher

KO | EN

gitlite — search

#javascript #python #hacktoberfest #react #ai #typescript #llm #go #golang #android #machine-learning #rust #deep-learning #linux

Adafruit_nRF51822_Flasher

(★ 44)

Wrapper for the Segger J-Link or STLink/V2 (via OpenOCD) to flash nRF51822 MCUs

Adafruit_nRF51822_Flasher 최신버젼 다운로드

최종 버전 다운로드 (.zip)

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

# Adafruit nRF51822 Flasher

**Table of Contents**

- [Requirements](#requirements)
  - [General Requirements](#general-requirements)
  - [Jlink Requirements](#jlink-requirements)
  - [STLink/V2 Requirements](#stlinkv2-requirements)
  - [RPi GPIO Requirements](#rpi-gpio-requirements)
- [Usage](#usage)

The flasher utility is a wrapper for various debuggers to flash nRF51822 MCUs with the official Adafruit firmware images.  Currently supported debuggers are:

- [Segger J-Link](https://www.adafruit.com/search?q=J-Link) (via [Adalink](https://github.com/adafruit/Adafruit_Adalink))
- [STLink/V2](https://www.adafruit.com/product/2548) (via [Adalink](https://github.com/adafruit/Adafruit_Adalink))
- Raspberry Pi GPIO (via an alpha version of OpenOCD, included in this repo)

This tool hides the implementation details of the different debuggers, and provides a means to flash Bluefruit LE modules with the specified softdevice, bootloader, and firmware via the SWD pins on the nRF51822 (SWDIO and SWCLK).

This is useful if you need to de-brick a board that failed a DFU update, or some other unfortunate event.

The [Adafruit_BluefruitLE_Firmware](https://github.com/adafruit/Adafruit_BluefruitLE_Firmware) folder is setup as a git submodule, linked to an external repo. you will need to clone this with --recursive flag

git clone --recursive git@github.com:adafruit/Adafruit_nRF51822_Flasher.git

If the folder is empty, you will need to run the following commands to fill it:

git submodule init
	git submodule update

If you aren't operating from a git repo, you can fill the `Adafruit_BluefruitLE_Firmware` folder from the command-line with the following command:

git clone git@github.com:adafruit/Adafruit_BluefruitLE_Firmware.git

## Requirements

### General Requirements
- One of the following SWD debuggers connected to the module via the SWD pins:
	- [Segger J-Link](https://www.adafruit.com/search?q=J-Link)
	- [STLink/V2](https://www.adafruit.com/product/2548)
	- Raspberry Pi (1 & 2) GPIO
- [Adalink](https://github.com/adafruit/Adafruit_Adalink) installed on your system (A Python JLinkExe wrapper used to flash the device)
	- git clone adalink
	- install and setup adalink
- [click](http://click.pocoo.org/4/) Python library:
	- `sudo apt-get install python-pip` or `sudo easy_install pip` then
	- `sudo pip install click`

### Jlink Requirements

Download and install jlink driver

### STLink/V2 Requirements

Install openOCD following the instruction in [Adalink doc](https://github.com/adafruit/Adafruit_Adalink#install-openocd)

On Linux or Raspberry Pi the following steps are required:

Install libusb:

sudo apt-get install libusb-dev libusb-1.0-0-dev

Configure UDEV permissions:

sudo cp openocd-0.9.0/contrib/99-openocd.rules /etc/udev/rules.d/
	sudo udevadm control --reload-rules

Then reboot.

**STLink/V2 to Bluefruit LE Pinout**

The following pins on the STLink/V2 need to be connected to the Bluefruit LE module:

STLink/V2 | Bluefruit LE
--------- | --------
RST       | RST
SWCLK     | SWCLK
SWDIO     | SWDIO
GND       | GND
3.3V      | VIN

### RPi GPIO Requirements

You can also use the RPi's raw GPIO to bit-bang JTAG/SWD signals, turning your RPi into a native debugger. A pre-built alpha version of openOCD binary is included in the `openocd-x.x.x/rpi_gpio/openocd` folder, since the current stable 0.9.0 does not support RPi GPIO with SWD interface yet. To sum up, you don't need install anything else except the libusb as follows

sudo apt-get install libusb-dev libusb-1.0-0-dev

Since accessing RPi's GPIO requires root access, sudo is required when executing the `flash.py` script:

**RPi 1 wiring**

![rpi_openocd_swd](https://cloud.githubusercontent.com/assets/249515/8418755/52657200-1edf-11e5-880f-4d80496e725e.png)

**RPi 2 wiring**

![rpi2_swd.png](https://cloud.githubusercontent.com/assets/249515/8327921/59465064-1a96-11e5-802f-827d6707686e.png)

NOTE: Don't forget to connect GND, remember that there are 4 wires in total.

## Usage

```
Usage: flash.py [OPTIONS]

Flash Bluefruit module Softdevice + Bootloader + Firmware

Options:
  --jtag TEXT           debugger must be "jlink" or "stlink" or "rpigpio",
                        default is "jlink"
  --softdevice TEXT     Softdevice version e.g "8.0.0"
  --bootloader INTEGER  Bootloader version e.g "1" or "2".
  --board TEXT          must be "blefriend32" or "blespifriend".
  --firmware TEXT       Firmware version e.g "0.6.5".
  --help                Show this message and exit.
```

`--firmware` and `--board` options are mandatory.

To flash the blefriend32 module using an STLink/V2 with SD 8.0.0, bootloader ver 2, firmware 0.6.5:

python flash.py --jtag=stlink --board=blefriend32 --softdevice=8.0.0 --bootloader=2 --firmware=0.6.5

To flash the above module with the same firmware using RPi GPIO
	
	sudo python flash.py --jtag=rpigpio --board=blefriend32 --softdevice=8.0.0 --bootloader=2 --firmware=0.6.5

Adafruit_nRF51822_Flasher

Adafruit_nRF51822_Flasher 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

Adafruit_nRF51822_Flasher

Adafruit_nRF51822_Flasher 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

Download README