xy-stage

KO | EN

gitlite — search

#hacktoberfest #ai #go #android #java #windows #awesome #kubernetes #vue #security #ios #mcp #openai #open-source

(★ 12)

mechanical stage

xy-stage 최신버젼 다운로드

최종 버전 다운로드 (.zip)

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

# Microscope XY Stage

[![assembled](https://raw.githubusercontent.com/koendv/xy-stage/main/pictures/assembled_small.jpg)](pictures/assembled.jpg)

This is a small computer-controlled mechanical microscope stage, with a movement of 2.4mm in both x and y, with a resolution of 5 &micro;m. Design goal is low component cost.

[![video](https://raw.githubusercontent.com/koendv/xy-stage/main/pictures/video_still.jpg)](https://vimeo.com/698148429)

[video](pictures/xy_stage.mp4) of the stage in motion.

[![disassembled](https://raw.githubusercontent.com/koendv/xy-stage/main/pictures/disassembled_small.jpg)](pictures/disassembled.jpg)

The stage consists of

- mechanical part
- adapter plates
- connector board
- arduino nano controller
- firmware

## mechanical part

[![mechanical](https://raw.githubusercontent.com/koendv/xy-stage/main/pictures/mechanical_small.jpg)](pictures/mechanical.jpg)

Picture of mechanical part (to the left) and connector board (to the right).
The mechanical part is the [motion compensation part of a digital camera](https://www.aliexpress.com/item/32972295033.html), bought from aliexpress. All signals are on a flat flexible cable.

The mechanical part consists of a small carriage, two stepper motors and two slotted optocouplers, one for x and one for y. The stepper motors have a step size of  10 &micro;m. The stepper motors are run in half-stepping mode, resulting in a resolution of  5 &micro;m.

## adapter plates

The adapter plates give the microscope stage a flat base to sit on, and a flat top to put a microscope slide on.

The [adapter plates](openscad/) are designed in openscad and 3D printed. The size of the carriage is 25mmx75mm, the same as a standard microscope slide. I've snipped a few plastic pieces off from the movement to make everything fit. Holes can be threaded with hand tapping tools, or reamed with a small drill.

## connector board

![pcb](https://raw.githubusercontent.com/koendv/xy-stage/main/pictures/pcb_assembly.jpg  "connector board")

The [connector board](easyeda/Schematic_xy%20stage%20breakout_2023-05-13.pdf) breaks out the flat cable to the arduino pins. The xy stage contains two optical endstops, one for x and one for y. This is the [schematic](pictures/xystage_endstop.pdf) of one such optical endstop. There are current-limiting resistors for the optocoupler led, and pull-down resistors for the optocoupler output.  The stepper motors are so small you can connect them directly to the microcontroller pins.

The flat cable connector has a small tab. Lift the tab to insert or remove the flat cable. Push the tab down to fix the flat cable in place.

The [board project is at easyeda](https://oshwlab.com/koendv/xy-stage-breakout); and I've put up [gerbers at github](easyeda/).

The easiest way to obtain a pcb board is to have it assembled for you. All files needed for pcb assembly are in the [easyeda](easyeda/) directory:

- Gerber files
- Bill of Materials ("BOM")
- Pick and Place file ("CPL")

The Gerber files order the printed circuit board. The Bill of Materials orders the components. The Pick and Place file orders the components to be soldered to the board.

This is a walk-through of the ordering process:

- Log in to [jlcpcb.com](https://jlcpcb.com/).
- Click "Order now"
- Click "Add gerber file"
- Select file "Gerber_PCB_xy stage breakout_2023-05-13.zip"
- Select "PCB Assemly"
- Choose "Assemble top side"
- Click "Confirm"
- Click "Next"
- Click "Add BOM File"
- Select file "BOM_PCB_xy stage breakout_2023-05-13.csv"
- Click "Add CPL File"
- Select file "PickAndPlace_PCB_xy stage breakout_2023-05-13.csv"
- Click "Process BOM and CPL"
- Next to the flat cable connector it says "No part selected". Click "Search". After the part has been found, click "Select".
- Click "Next"
- In product description, choose "Research/Education/DIY/Entertainment", "DIY"
- Click "Save to cart"
- Check out order

Make sure all parts are available before ordering assembly.

## arduino nano controller

The microcontroller is a 5V 16MHz arduino nano. This processor was chosen because it can drive the stepper motor pins directly, at low cost. The arduino nano plugs in in the connector board.

Two firmware are available for the xy stage: an arduino sketch and the grbl g-code motion controller.

## arduino sketch

The [arduino/ directory](arduino/) contains an arduino project for the xy stage.
To install this firmware in the arduino nano, start up the arduino IDE. Open the file [xystage.ino](arduino/xystage/xystage.ino) in the arduino IDE,
In the arduino IDE, choose "Tools -> Board -> Arduino AVR Boards -> Arduino Nano", compile and upload.

Connect to the arduino serial port with a terminal emulator, and get this prompt:

```
xy stage - w forward s backward a left d right x home
ok
```

Move the stage using the WASD keys: w is forward, s is backward, a is left, d is right. x homes the stage, and if you press shift the stage moves ten times faster.

| key | action |
|---|---|
| w | forward 1 step |
| s | backward 1 step |
| a | left 1 step |
| d | right 1 step |
| W | forward 10 steps |
| S | backward 10 steps |
| A | left 10 steps |
| D | right 10 steps |
| x | home |

If after power-up the led blinks and the serial console prints  ``error`` then homing failed. Check the flat flexible cable connections, and that the carriage can move freely.

## grbl

[![grbl logo](https://raw.githubusercontent.com/koendv/xy-stage/main/pictures/grbl_logo_150px.png)](https://github.com/gnea/grbl/wiki)

[grbl](https://github.com/gnea/grbl/wiki) is a g-code motion controller for the arduino nano. grbl allows stage control using G-code commands.

Example: Set the feed rate. Starting at the origin, first move the stage 1 mm in x, then 1 mm in y.

```
> Grbl 1.1h ['$' for help]
< F100
> ok
< G1X1
> ok
< G1Y1
> ok
```

See the [grbl/ directory](grbl/) for grbl firmware for the arduino nano.

Using G-code is interesting if you wish to automate a microscope.

## micro-manager

[micro-manager](https://micro-manager.org/) is open source software for control and automation of microscope hardware. See the [micro-manager/ directory](micro-manager/) for using the xy-stage with micro-manager.

## closing thoughts

Looking back, the adapter plates could easily be improved. The adapter plates were printed in yellow, on a Prusa FDM printer. If I had to do this again, I would 3D print the adapter plates in a matte dark grey or black, not yellow. Using SLS or MJF, not FDM, to be able to design a carriage that weighs less yet is more rigid. And probably ordered at [jlcpcb](https://3d.jlcpcb.com/), the same place I had the printed circuits made.

## bill of Materials

The list of materials used to build this project:

|Name|Part|Qty|
|---|---|---|
|R1, R3|470R 0603|2|
|R2, R4|18K 0603|2|
|U1|Hirose FH26W-15S-0.3SHW(60)|1|
||20pin 2.54mm single row female header|2|
||arduino nano 3.0 atmega328|1|
||[small xy stage](https://www.aliexpress.com/item/32972295033.html)|1|
||M2x8 screw|3|
||pcb|1|
||3D printed parts|1|

[![ko-fi](https://raw.githubusercontent.com/koendv/xy-stage/main/pictures/kofibutton.svg)](https://ko-fi.com/Q5Q03LPDQ)

xy-stage

xy-stage 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

xy-stage

xy-stage 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

Download README