KO | EN

GitLite

Minimalist Open Source Repository Search Engine

gitlite — search

#dsh #dsh-plugin #developer-tools #ai-agent #claude-code #codex #typescript #ai-agents #deepseek-harness #mcp #cli #rust

WiFi-Signal-Strength-Checker

★ 15 Open GitHub ↗

Simple tool to check the WiFi strength at your office or home. Check WiFi signal strength using ESP8266(NodeMCU/Wemos).

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

![github-small](https://raw.githubusercontent.com/shivasiddharth/WiFi-Signal-Strength-Checker/main/Images/Handheld_16-9.jpg)

# WiFi Signal Strength Checker
 Simple tool to check the WiFi signal strength at your office or home.

## Parts required   
1. NodeMCU or Wemos D1 Mini  
   Purchase links:                 
   1. Amazon:  
      1. US: https://amzn.to/3vk56Ln   
      2. UK: https://amzn.to/3rPuMgW    
      3. Spain: https://amzn.to/3bGlHBf    
      4. Italy: https://amzn.to/3qKnnhm   
      5. Germany: https://amzn.to/3lcHyn0       
      6. India: https://amzn.to/3cxXKey                           
   2. Ebay:      
      1. https://ebay.us/hu7zJM    
      2. https://ebay.us/yhG7Da     
      3. https://ebay.us/loeNEr     
      4. https://ebay.us/JF5QYD

2. SSD1306 OLED Display   
   Purchase links:    
   1. Amazon:    
      1. US: https://amzn.to/3qKK0lU  
      2. UK: https://amzn.to/30FgqU6     
      3. Spain: https://amzn.to/3bK4Ttf    
      4. Italy: https://amzn.to/3rNfuce   
      5. Germany: https://amzn.to/3tib8dD          
      6. India: https://amzn.to/2OudLdB     
   2. Ebay:       
      1. https://ebay.us/VkHi7j     
      2. https://ebay.us/F2lqOy        
      3. https://ebay.us/9swiZ4

3. General Purpose PCB   
   Purchase links:    
   1. Amazon:     
      1. US: https://amzn.to/3ey6UKR     
      2. UK: https://amzn.to/3rHkrU2        
      3. Spain: https://amzn.to/3rG5uBH       
      4. Italy: https://amzn.to/3bJKJiX      
      5. Germany: https://amzn.to/3tmsUfX             
      6. India: https://amzn.to/3llFfOz                   
   2. Ebay:     
      1. https://ebay.us/ZmFTcu

4. USB to Micro USB Mini adapter  
   Purchase links:     
   1. Amazon:   
      1. US: https://amzn.to/3tha4H4        
      2. UK: https://amzn.to/3bI4Q12           
      3. Spain: https://amzn.to/3tjUbzI          
      4. Italy: https://amzn.to/3lmz2SE https://amzn.to/3rP5y1W      
      5. Germany: https://amzn.to/38zQa28 https://amzn.to/30Gf4IV                 
      6. India: https://amzn.to/3qLvCKj              
   2. Ebay:       
      1. https://ebay.us/r8BBUG   
      2. https://ebay.us/tnmWOc  
      3. https://ebay.us/jLesSJ

5. Portable power bank   
6. Header Pins    
7. Wires   
8. Soldering iron   
9. Lead-free solder    
10. Soldering flux

## PCB Wiring   
The easy way out and to save hassles of soldering, you could probably use the Wemos's OLED Display addon. But the addon screen is just 0.66". There are larger displays availble, but you need to get your hands dirty and make the connections. The Wemos D1 Mini - OLED Display wiring is shown below. In the diagram below, the display's SCL pin is connected to Wemos's D1 pin, display's SDA pin is connected to Wemos's D2 pin, display's ground to Wemos's ground and display's Vcc to Wemos's 3.3V pin. Just in case you wish to make a single PCB of the Wemos and the display, you can design the PCB in Fritzing and get the PCBs printed from https://jlcpcb.com.

## Getting the I2C Address 
After putting all the parts together, the Wemos or the NodeMCU is ready to be programmed. Most of the SSD1306 I2C OLED displays have the default address set to ```0x3c```. Just to double check, I would suggest you to run an I2C address scan. My library suggestion is the "i2cdetect" by [Mike Causer](https://github.com/mcauser). <img src="https://github.com/shivasiddharth/WiFi-Signal-Strength-Checker/raw/main/Images/I2C_Scanner_Library.jpg"> Use the i2cdetect example to check for the OLED's address. <img src="https://github.com/shivasiddharth/WiFi-Signal-Strength-Checker/raw/main/Images/I2C_Detect_Example.jpg"> After uploading the sketch, open the serial monitor and set the baud rate to the value given in the code to see the detected address as shown below. <img src="https://github.com/shivasiddharth/WiFi-Signal-Strength-Checker/raw/main/Images/Serial_Monitor_I2C_Detect.jpg">

## SSD1306 Library 
There are a number of different libraries for the SSD1306 based chipset. The one that I have used is the ["ESP8266 and ESP32 OLED driver for SSD1306 displays"](https://github.com/ThingPulse/esp8266-oled-ssd1306). This library <img src="https://github.com/shivasiddharth/WiFi-Signal-Strength-Checker/raw/main/Images/SSD1306_Library.jpg"> works great.

## Arduino Code   
In the arduino code set your WiFi credentials    
```
char wifissid[] = "ENTER YOUR WiFi SSID HERE";    
char wifipass[] = "ENTER YOUR WiFi PASSWORD HERE";    
```

Normally, the signal strength is displayed in dBm. But for a non techie person, the signal strength in terms of % would appeal more. Catering to people from both the spectrum, the program is set to display the signal values in both dBm and %. The dBm scale is non-linear or other words logarithmic. I have used values from this [article](https://www.intuitibits.com/2016/03/23/dbm-to-percent-conversion/) in this program to map the signal strength in dBm to %.    
```    
int signal_dBM[] = { -100, -99, -98, -97, -96, -95, -94, -93, -92, -91, -90, -89, -88, -87, -86, -85, -84, -83, -82, -81, -80, -79, -78, -77, -76, -75, -74, -73, -72, -71, -70, -69, -68, -67, -66, -65, -64, -63, -62, -61, -60, -59, -58, -57, -56, -55, -54, -53, -52, -51, -50, -49, -48, -47, -46, -45, -44, -43, -42, -41, -40, -39, -38, -37, -36, -35, -34, -33, -32, -31, -30, -29, -28, -27, -26, -25, -24, -23, -22, -21, -20, -19, -18, -17, -16, -15, -14, -13, -12, -11, -10, -9, -8, -7, -6, -5, -4, -3, -2, -1};
int signal_percent[] = {0, 0, 0, 0, 0, 0, 4, 6, 8, 11, 13, 15, 17, 19, 21, 23, 26, 28, 30, 32, 34, 35, 37, 39, 41, 43, 45, 46, 48, 50, 52, 53, 55, 56, 58, 59, 61, 62, 64, 65, 67, 68, 69, 71, 72, 73, 75, 76, 77, 78, 79, 80, 81, 82, 83, 84, 85, 86, 87, 88, 89, 90, 90, 91, 92, 93, 93, 94, 95, 95, 96, 96, 97, 97, 98, 98, 99, 99, 99, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100};
```

I made some quick calculations and indeed this is the closest representation that you can get.

Set your display's address and the pins used if it is different from the one given in the code.  
```    
SSD1306  display(0x3c, D2, D1);    
```    
It follows the format   
```   
SSD1306 display(Address of Display, SDA_PIN, SCL_PIN)  
```

Based on the orientation of the display, you can either comment out or retain the command to flip the display.   
```   
display.flipScreenVertically()    
```

## Demo   
Checkout the following video to see the device in action.

[![](http://img.youtube.com/vi/VM3Onk-PZtA/0.jpg)](http://www.youtube.com/watch?v=VM3Onk-PZtA "")

WiFi-Signal-Strength-Checker

Explore Similar Repositories

Was this content helpful?

Recent Feedback

Download README