mkconnect-python

KO | EN

gitlite — search

#react #typescript #llm #deep-learning #linux #nodejs #java #windows #awesome #kubernetes #awesome-list #security #openai #open-source

mkconnect-python

(★ 14)

a bit of code to connect to MouldKing bluetooth bricks in python

mkconnect-python 최신버젼 다운로드

최종 버전 다운로드 (.zip)

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

# mkconnect-python
...a bit of code to connect to MouldKing Bluetooth Hubs in python.

# MouldKing Hubs
## MouldKing 6.0 Hub
The MouldKing 6.0 Hub has two modes:
* RC-Mode to be controlled with a MouldKing remotecontrol
* Bluetooth-Mode to be controlled with an app

You can control a maximum of three MK6.0 Hubs at the same time with bluetooth.
> (Currently this project can send only one advertising telegram the same time - so only one hub can be controlled, all others will go in timeout-mode till next telegram with their device address is sent.)

## Setting the address of the Hub
To switch the Hub's device address to the next one (device 0, device 1, device 2) just press the button on the hub.

> i.E.: If the script runs with **mkcontrol(2,0,1)** (-> device2, channel0, full speed forward) and nothing is happening, you have to short-press the button, perhaps again...)

# usage
Start the script [consoletest.py](https://github.com/J0EK3R/mkconnect-python/blob/main/consoletest.py) on your raspberry:
```
pi@devpi:~/dev/mkconnect-python $ sudo python -i consoletest.py 
```

## mkbtstop() - stop bluetooth advertising
```
Ready to execute commands

>>> mkbtstop()
```

## mkconnect() - switch hubs in bluetooth mode
If you power-on the hubs they will listen to telegrams to the **first device by default**.
Call mkconnect() to switch all hubs in Bluetooth mode.
By short-pressing the button on MK6.0 Hubs you can choose the hubId:
* hubId=0 - one Led flash
* hubId=1 - two Led flashs
* hubId=2 - three Led flashs
```
Ready to execute commands

>>> mkconnect()
```

## mkcontrol(deviceId, channel, power and powerAndDirection)
i.E.: mkcontrol(0, 0, 1) - on first device (deviceId=0) run channel A (channel=0) with fullspeed (powerAndDirection=1)
```
Ready to execute commands

>>> mkcontrol(0, 0, 1)
```

## mkstop(deviceId)
Set all channels of device to zero
```
Ready to execute commands

>>> mkstop(0)
```

---
# old stuff

There is a testscript [consoletest.py](https://github.com/J0EK3R/mkconnect-python/blob/main/consoletest.py) where (on raspberry pi) **hcitool** is used to advertise telegrams over bluetooth.

Maybe you habe to **sudo** the command:
```
pi@devpi:~/dev/mkconnect-python $ sudo python -i consoletest.py

Ready to execute commands

For connecting: mkconnect(hubId) ex: mkconnect(0) or mkconnect(1) for the second hub

Available commands: mkconnect(hubId)
 mkstop(hubId)
 mkcontrol(deviceId, channel, powerAndDirection)

ex: mkcontrol(0, 0, 0.5) ; mkcontrol(0, 'B', -1)
 the minus sign - indicate reverse motor direction
```

Just look in [main.py](https://github.com/J0EK3R/mkconnect-python/blob/main/main.py) for current usage...

Current output in [https://wokwi.com/projects/new/micropython-pi-pico](https://wokwi.com/projects/398314618803830785)
...looks very good! :)
```
connect-telegram
rawdata: 6d 7b a7 80 80 80 80 92
crypted: 6d b6 43 cf 7e 8f 47 11 88 66 59 38 d1 7a aa 26 49 5e 13 14 15 16 17 18

stop-telegram
rawdata: 61 7b a7 80 80 80 80 80 80 9e
crypted: 6d b6 43 cf 7e 8f 47 11 84 66 59 38 d1 7a aa 34 67 4a 55 bf 15 16 17 18

C1: fullspeed forwards
rawdata: 61 7b a7 ff 80 80 80 80 80 9e
crypted: 6d b6 43 cf 7e 8f 47 11 84 66 59 47 d1 7a aa 34 67 4a ed b7 15 16 17 18

C1: halfspeed forwards
rawdata: 61 7b a7 bf 80 80 80 80 80 9e
crypted: 6d b6 43 cf 7e 8f 47 11 84 66 59 07 d1 7a aa 34 67 4a eb 70 15 16 17 18

C1: halfspeed backwards
rawdata: 61 7b a7 40 80 80 80 80 80 9e
crypted: 6d b6 43 cf 7e 8f 47 11 84 66 59 f8 d1 7a aa 34 67 4a 4e fe 15 16 17 18

C2: halfspeed backwards
rawdata: 61 7b a7 40 40 80 80 80 80 9e
crypted: 6d b6 43 cf 7e 8f 47 11 84 66 59 f8 11 7a aa 34 67 4a 3d f9 15 16 17 18
MicroPython v1.22.0 on 2023-12-27; Raspberry Pi Pico with RP2040
Type "help()" for more information.
>>> 
raw REPL; CTRL-B to exit
>
```

mkconnect-python

mkconnect-python 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

mkconnect-python

mkconnect-python 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

Download README