KO | EN

GitLite

Minimalist Open Source Repository Search Engine

gitlite — search

#dsh #dsh-plugin #ai-agents #developer-tools #codex #claude-code #mcp #rust #deepseek-harness #typescript #ai-agent #cli

ZigUSB

★ 38 Open GitHub ↗

Zigbee USB power monitor and switch

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

# ZigUSB

## New version of this device - [ZigUSB C6](https://github.com/xyzroe/ZigUSB_C6)

ZigUSB was developed as a device that allows you to control and monitor the power of a device connected via USB.

Using this device, you can remotely control the power of the USB port to turn on or off the connected device. And also monitor the current voltage and current. And it's not a bad Zigbee network router.

Frequent use cases: converting a "stupid" USB lamp into a "smart" one; connecting modems / sticks / adapters, which sometimes require a power reset; monitoring the current consumption of any connected device.

Possibilities:
- Power on/off by push button and via Zigbee network.
- Automatic restart loop of the connected device with a single Zigbee command.
- Monitoring of voltage and current supplied to the connected device, INA219 chip.
- Setting the maximum USB current using a variable resistor on the board (1.0-3.2A)
- For power management, a MIC2545A USB switch chip is used.
- E18-MS1PA2-PCB (CC2530 with +20dBi amplifier) was used as the Zigbee chip, which allows it to be used in remote places, and at the same time act as a good router for other devices.
- USB data transfer is available. This may be needed when connecting a USB modem to a router that does not know how to manage USB power, and the modem may need to be rebooted.
- Designed for AK-N-12 case.
- To re-pairing or reset to factory defaults:  
 **Power on (plug into power source), wait 2 seconds, power off (remove from power source), repeat this cycle three times.** 
  
  
### Overview  
  
#### Touch version  
<div align="center">
<img width="40%" src="https://raw.githubusercontent.com/xyzroe/ZigUSB/main/images/top_touch.png">
<img width="40%" src="https://raw.githubusercontent.com/xyzroe/ZigUSB/main/images/bottom_touch.png">
</div>

#### Button version  
<div align="center">
<img width="40%" src="https://raw.githubusercontent.com/xyzroe/ZigUSB/main/images/top.png">
<img width="40%" src="https://raw.githubusercontent.com/xyzroe/ZigUSB/main/images/bottom.png">
</div>

### Photos

#### Touch version  
<table>
<tr>
<td width="50%">
<img src="https://raw.githubusercontent.com/xyzroe/ZigUSB/main/images/top_case_touch.jpeg">
</td>
<td>
<img src="https://raw.githubusercontent.com/xyzroe/ZigUSB/main/images/back_case_touch.jpeg">
</td>
</tr>
</table>

#### Button version  
<table>
<tr>
<td width="50%">
<img src="https://raw.githubusercontent.com/xyzroe/ZigUSB/main/images/top_case.jpeg">
</td>
<td>
<img src="https://raw.githubusercontent.com/xyzroe/ZigUSB/main/images/back_case.jpeg">
</td>
</tr>
<tr>
<td width="50%">
<img src="https://raw.githubusercontent.com/xyzroe/ZigUSB/main/images/top_pcb.jpeg">
</td>
<td>
<img src="https://raw.githubusercontent.com/xyzroe/ZigUSB/main/images/back_pcb.jpeg">
</td>
</tr>
</table>

### Schematic
<div align="center"><img width="90%" src="https://raw.githubusercontent.com/xyzroe/ZigUSB/main/hardware/Schematic_ZigUSB.png"></div>
<div align="center"><img width="90%" src="https://raw.githubusercontent.com/xyzroe/ZigUSB/main/hardware/Schematic_ZigUSB_touch.png"></div>

### PTVO Config

#### Touch version  
<div align="center"><img width="70%" src="https://raw.githubusercontent.com/xyzroe/ZigUSB/main/images/ptvo_1_touch.png"></div>

#### Button version  
<div align="center"><img width="70%" src="https://raw.githubusercontent.com/xyzroe/ZigUSB/main/images/ptvo_1.png"></div>

#### zigbee2mqtt & Home Assistant overview

</div>

### Hardware files

#### Touch version  
[Gerber](https://raw.githubusercontent.com/xyzroe/ZigUSB/main/hardware/Gerber_ZigUSB_touch.zip)  
[BOM](https://raw.githubusercontent.com/xyzroe/ZigUSB/main/hardware/BOM_ZigUSB_touch.csv)  or  [iBOM](https://xyzroe.cc/ZigUSB/hardware/iBOM_ZigUSB_touch.html)  🚀

#### Button version  
[Gerber](https://raw.githubusercontent.com/xyzroe/ZigUSB/main/hardware/Gerber_ZigUSB.zip)  
[BOM](https://raw.githubusercontent.com/xyzroe/ZigUSB/main/hardware/BOM_ZigUSB.csv)  or  [iBOM](https://xyzroe.cc/ZigUSB/hardware/zigbee_usb_power_switch_final_rev0.html)  🚀

### Firmware files
[NEW z2m external converter](https://github.com/xyzroe/ZigUSB/tree/main/firmware/ZigUSB_updated.js) 🎉 (for new z2m ext converter format)  **with NEW image**  
[old z2m external converter](https://github.com/xyzroe/ZigUSB/tree/main/firmware/ZigUSB.js)  
   
[All FW .hex, PTVO .ini, .txt and converter .js files](https://github.com/xyzroe/ZigUSB/tree/main/firmware)  
  
### Verified supported Zigbee systems:  
1. [zigbee2mqtt](https://www.zigbee2mqtt.io/) - FULL support, no more need [external converter](https://github.com/xyzroe/ZigUSB/tree/main/firmware/ZigUSB_updated.js) ⭐⭐⭐⭐⭐
2. [Homey](https://homey.app/) - FULL support, [more info](https://homey.app/a/cc.xyzroe.zigusb/). Thanks to [
Arun Babu Neelicattu](https://github.com/abn) ⭐⭐⭐⭐⭐
3. [HOMEd](https://wiki.homed.dev/page/HOMEd) - partial support. On-off control inversed. ⭐⭐⭐⭐
4. [ZHA](https://www.home-assistant.io/integrations/zha/) - partial support. No current and voltage sensor, no ability to restart USB device, on-off control inversed. ⭐⭐⭐
5. Samsung Smartthings Hub - partial support. No sensors, no ability to restart USB device, on-off control inversed. ⭐⭐⭐

other systems supported Zigbee should also work, but need testing.

### Where to buy?  
Tindie stopped supporting shipments from Ukraine, so now you can only buy on my partners’ website (shipping worldwide)  
  
<a href="https://mind.in.ua/"><img src="https://static.tildacdn.com/tild3433-3934-4565-b362-386238366331/logo_full.png" alt="Go to mind.in.ua" height="120"></a>

### Like ♥️?
[!["Buy Me A Coffee"](https://www.buymeacoffee.com/assets/img/custom_images/orange_img.png)](https://www.buymeacoffee.com/xyzroe)

<br>

[![Made in Ukraine](https://img.shields.io/badge/made_in-ukraine-ffd700.svg?labelColor=0057b7)](https://stand-with-ukraine.pp.ua)

### Inspired by
1. The original project of USB switch by [Kasito](https://kasito.ru/zigbee-vyklyuchatel-usb-nagruzki/)
2. Zigbee configurable firmware [PTVO](https://ptvo.info)

<br>  
ZigUSB is licensed under the

[GNU General Public License v3.0](https://raw.githubusercontent.com/xyzroe/ZigUSB/main/LICENSE)

ZigUSB

Explore Similar Repositories

Was this content helpful?

Recent Feedback

Download README