linux-x1e80100-zenbook-a14

KO | EN

gitlite — search

#go #golang #android #machine-learning #linux #docker #macos #cli #kubernetes #awesome-list #vue #pytorch #ios #open-source

linux-x1e80100-zenbook-a14

(★ 79)

Patches to support Asus Zenbook A14 with Snapdragon X1 Elite / X1 Plus

linux-x1e80100-zenbook-a14 Latest Version Download

Download Latest Version (.zip)

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

### Patches for supporting Asus Zenbook A14 2025, models UX3407QA, UX3407RA.

As changes will be merged upstream, redundant patches will be dropped from this repo, to only maitain diff on top of latest `linux-next`.

## Test setup
Kernel
* `linux-next`
* current patchset tested on `next-20260109`

Initramfs
* Ubuntu's auto-built from kernel installation

HW configurations tested
* UX3407QA
* x1-26-100
* 1920x1200 OLED non-touch 60Hz
* 32GB RAM

## Feature Matrix

* WIP - Something I am already working on
* TBH - Something I could work on, but not started / no sufficient progress was made
* QC  - Something I cannot work on, depends on Qualcomm's upstream support

| Feature                 | Status | Notes                                                                                                        |
| ----------------------- | -----: | ------------------------------------------------------------------------------------------------------------ |
| Battery Charging        |     ✅ |                                                                                                              |
| Battery Info            |     ✅ | Requires firmware extract                                                                                    |
| Bluetooth               |     ✅ |                                                                                                              |
| Iris/HW decoder         |    WIP | Works on Hamoa (X1E variant), not starting on Purwa (X1P variant)                                            |
| Camera                  |    WIP | Works on top of Bryan/Linaro tree. Stable on Hamoa (X1E variant), not fully working on Purwa (X1P variant)   |
| Display                 |     ✅ | FHD OLED and LCD on UX3407QA, 3K OLED on UX3407RA                                                            |
| GPU Acceleration        |     ✅ | Requires firmware extract                                                                                    |
| Keyboard                |     ✅ |                                                                                                              |
| Microphone              |     ✅ |                                                                                                              |
| NVMe                    |     ✅ |                                                                                                              |
| Speakers                |     ✅ | ~Requires userland configuration, see below.~ Works with latest upstream alsa-ucm-config, linux-firmware     |
| Audio Jack              |     ✅ |                                                                                                              |
| Suspend                 |     ✅ | Suspends well, lid switch working. Power drop in sleep isn't best, depends on X1E generic support.           |
| Touchpad                |     ✅ |                                                                                                              |
| TPM                     |     ❌ | Firmware TPM                                                                                                 |
| USB-A 3.0               |     ✅ | Requires firmware extract                                                                                    |
| USB-C 3.0               |     ✅ |                                                                                                              |
| USB-C Booting           |     ✅ |                                                                                                              |
| USB-C DP Alt Mode       |     ✅ | Requires firmware extract                                                                                    |
| USB-C DP over dock      |     ✅ |                                                                                                              |
| HDMI                    |     ✅ |                                                                                                              |
| Wi-Fi                   |     ✅ | UX3407RA with FastConnect 7800 should work oob. UX3407QA requires firmware extraction and patching.          |
| EC                      |     ❌ | Similar to out-of-tree EC driver for Lenovo Slim 7x.                                                         |

## WCN688x WiFi

Lower-end UX3407QA has WCN6885 WiFi 6E, as opposed to WiFi 7 on UX3407RA.
At least the WCN6885 is known not to work as is, as it requires both newer firmware, and patched `boards-2.bin`. Without these changes, driver would fail to load:
```bash
$ dmesg -w
...
[ 3190.482952] ath11k_pci 0004:01:00.0: BAR 0 [mem 0x7c400000-0x7c5fffff 64bit]: assigned
[ 3190.485446] ath11k_pci 0004:01:00.0: MSI vectors: 32
[ 3190.485465] ath11k_pci 0004:01:00.0: wcn6855 hw2.1
[ 3190.649874] mhi mhi0: Requested to power ON
[ 3190.649907] mhi mhi0: Power on setup success
[ 3190.732860] mhi mhi0: Wait for device to enter SBL or Mission mode
[ 3191.354711] ath11k_pci 0004:01:00.0: chip_id 0x2 chip_family 0xb board_id 0xff soc_id 0x400c0210
[ 3191.354723] ath11k_pci 0004:01:00.0: fw_version 0x11088190 fw_build_timestamp 2024-10-17 19:57 fw_build_id WLAN.HSP.1.1.c5-00400-QCAHSPSWPL_V1_V2_SILICONZ_WOS-1
[ 3191.412843] ath11k_pci 0004:01:00.0: failed to fetch board data for bus=pci,vendor=17cb,device=1103,subsystem-vendor=14cd,subsystem-device=950a,qmi-chip-id=2,qmi-board-id=255,variant=UX3407Q from ath11k/WCN6855/hw2.1/board-2.bin
[ 3191.412853] ath11k_pci 0004:01:00.0: failed to fetch board data for bus=pci,vendor=17cb,device=1103,subsystem-vendor=14cd,subsystem-device=950a,qmi-chip-id=2,qmi-board-id=255 from ath11k/WCN6855/hw2.1/board-2.bin
[ 3191.412856] ath11k_pci 0004:01:00.0: failed to fetch board data for bus=pci,qmi-chip-id=2 from ath11k/WCN6855/hw2.1/board-2.bin
[ 3191.412858] ath11k_pci 0004:01:00.0: failed to fetch board.bin from WCN6855/hw2.1
```

### Extract firmware from windows path
```bash
# Find location of driver on Windows partition
WINDOWS_DRIVER="/mnt/c/Windows/System32/DriverStore/FileRepository/qcwlanhsp8380.inf_arm64_ecbde8f5eb2c6dd5/"

# Copy firmware
sudo cp ${WINDOWS_DRIVER}/wlanfw20.mbn /lib/firmware/updates/ath11k/WCN6855/hw2.1/amss.bin
sudo cp ${WINDOWS_DRIVER}/regdb.bin /lib/firmware/updates/ath11k/WCN6855/hw2.1/regdb.bin
sudo cp ${WINDOWS_DRIVER}/m3.bin /lib/firmware/updates/ath11k/WCN6855/hw2.1/m3.bin
```

### Repack `board-2.bin`

```bash
$ mkdir -p /tmp/qca

# Identify and copy board config for you platform
# - It will be `.elf` file of ~59KB
# - Match based on device name, in this case `UX3407Q`
% cp ${WINDOWS_DRIVER}/bdwlan_wcn685x_2p1_nfa725a_UX3407Q.elf /tmp/qca/

# Copy and decompress current `board-2.bin`
$ cp /usr/lib/firmware/ath11k/WCN6855/hw2.0/board-2.bin.zst /tmp/qca/board-2_original.bin.zst
$ zstd -d /tmp/qca/board-2_original.bin.zst

# Unpack `board-2.bin`
# This requires QCA tool, available at:
# https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath11k/ath11k-bdencoder

$ ./ath11k-bdencoder -e /tmp/qca/board-2_original.bin

# Patch to add required entry, matching target name
# Inspect `board-2.json`. Compare to error in dmesg, eg:
$ dmesg | grep "failed to fetch board data for"
[   13.546264] ath11k_pci 0004:01:00.0: failed to fetch board data for bus=pci,vendor=17cb,device=1103,subsystem-vendor=14cd,subsystem-device=950a,qmi-chip-id=2,qmi-board-id=255,variant=UX3407Q from ath11k/WCN6855/hw2.1/board-2.bin
[   13.546273] ath11k_pci 0004:01:00.0: failed to fetch board data for bus=pci,vendor=17cb,device=1103,subsystem-vendor=14cd,subsystem-device=950a,qmi-chip-id=2,qmi-board-id=255 from ath11k/WCN6855/hw2.1/board-2.bin
[   13.546275] ath11k_pci 0004:01:00.0: failed to fetch board data for bus=pci,qmi-chip-id=2 from ath11k/WCN6855/hw2.1/board-2.bin

# Extract 1st entry which is the most precise match:
# "bus=pci,vendor=17cb,device=1103,subsystem-vendor=14cd,subsystem-device=950a,qmi-chip-id=2,qmi-board-id=255,variant=UX3407Q"

# Add apropriate entry to `board-2.json`. On UX3407QA I have seen `qmi-chip-id` being both `2` and `18`, adjust accordingly:
             {
                 "names": [
                     "bus=pci,vendor=17cb,device=1103,subsystem-vendor=14cd,subsystem-device=9509,qmi-chip-id=2,qmi-board-id=255"
                 ],
                 "data": "bus=pci,vendor=17cb,device=1103,subsystem-vendor=14cd,subsystem-device=9509,qmi-chip-id=2,qmi-board-id=255.bin"
             },
+            {
+                "names": [
+                    "bus=pci,vendor=17cb,device=1103,subsystem-vendor=14cd,subsystem-device=950a,qmi-chip-id=2,qmi-board-id=255,variant=UX3407Q"
+                ],
+                "data": "bus=pci,vendor=17cb,device=1103,subsystem-vendor=14cd,subsystem-device=950a,qmi-chip-id=2,qmi-board-id=255,variant=UX3407Q.bin"
+            },
             {
                 "names": [

# Rename copied-out elf file to the board name format
$ mv /tmp/qca/bdwlan_wcn685x_2p1_nfa725a_UX3407Q.elf /tmp/qca/"bus=pci,vendor=17cb,device=1103,subsystem-vendor=14cd,subsystem-device=950a,qmi-chip-id=2,qmi-board-id=255,variant=UX3407Q.bin"

# Repack `board-2.bin`
$ ./ath11k-bdencoder -c /tmp/qca/board-2.json

# Finally, compress the new `board-2.bin` and copy it to destination
$ zstd /tmp/qca/board-2.bin
$ sudo cp /tmp/qca/board-2.bin.zst /lib/firmware/updates/ath11k/WCN6855/hw2.1/board-2.bin.zst
```

### Reload kernel module
```bash
$ sudo modprobe -r ath11k_pci ath11k
$ sudo modprobe ath11k_pci

# You should now see the wifi driver to start normally
$ dmesg -w
...
[ 3228.406613] ath11k_pci 0004:01:00.0: BAR 0 [mem 0x7c400000-0x7c5fffff 64bit]: assigned
[ 3228.409524] ath11k_pci 0004:01:00.0: MSI vectors: 32
[ 3228.409545] ath11k_pci 0004:01:00.0: wcn6855 hw2.1
[ 3228.577327] mhi mhi0: Requested to power ON
[ 3228.577364] mhi mhi0: Power on setup success
[ 3228.924764] mhi mhi0: Wait for device to enter SBL or Mission mode
[ 3229.547159] ath11k_pci 0004:01:00.0: chip_id 0x2 chip_family 0xb board_id 0xff soc_id 0x400c0210
[ 3229.547171] ath11k_pci 0004:01:00.0: fw_version 0x11088190 fw_build_timestamp 2024-10-17 19:57 fw_build_id WLAN.HSP.1.1.c5-00400-QCAHSPSWPL_V1_V2_SILICONZ_WOS-1
[ 3229.866703] ath11k_pci 0004:01:00.0 wlP4p1s0: renamed from wlan0
[ 3229.874853] ath11k_pci 0004:01:00.0: Failed to set the requested Country regulatory setting
[ 3229.874861] ath11k_pci 0004:01:00.0: failed to process regulatory info -22
[ 3229.875182] ath11k_pci 0004:01:00.0: Failed to set the requested Country regulatory setting
[ 3229.875183] ath11k_pci 0004:01:00.0: failed to process regulatory info -22
[ 3236.596237] wlP4p1s0: authenticate with 50:64:2b:5f:e3:ba (local address=8c:3b:4a:a6:fa:f3)
[ 3236.596250] wlP4p1s0: send auth to 50:64:2b:5f:e3:ba (try 1/3)
[ 3236.601170] wlP4p1s0: authenticated
```

## Audio configuration

Besides device tree changes in kernel, two things are required to get audio working: alsa configuration and toplogy firmware.

### Audioreach-topology
_Latest `linux-next` contains required binaries. Alternatively, compile from source as follows_

* Download latest sources with Asus Zenbook A14 support from https://github.com/linux-msm/audioreach-topology/
* Build via
```bash
cmake .
cmake --build .
```
* Install compiled binary to firmware path via
```bash
sudo cp qcom/x1e80100/ASUSTeK/zenbook-a14/X1E80100-ASUS-Zenbook-A14-tplg.bin /lib/firmware/updates/qcom/x1e80100/X1E80100-ASUS-Zenbook-A14-tplg.bin
```

### Alsa configuration
_Latest `alsa-ucm-conf` contains required configuration. Alternatively, retreive from source as follows_

* Download lastet configuration with Asus Zenbook A14 support from https://github.com/alsa-project/alsa-ucm-conf
* Follow instructions in `README.md` to unpack

Reboot to apply changes. You should now have:
* Working x2 speakers
* Working x2 microphones
* Working audio jack with microphone (* it appears microphone in headset is not working anymore, being looked into)
* Working audio over HDMI, Type-C DisplayPort monitor

## Camera configuration

The camera requires `libcamera` to function, and can be tested with `qcam` (part of `libcamera-tools`). However, for it to work with user-space app including browser, it must be accessible via pipewire. Sample output:

```bash
$ wpctl status
PipeWire 'pipewire-0' [1.2.7, ...]
...
Video
 ├─ Devices:
 │      51. Qualcomm Camera Subsystem           [v4l2]
 │      52. Qualcomm Camera Subsystem           [v4l2]
 │      53. Qualcomm Camera Subsystem           [v4l2]
 │      54. Qualcomm Camera Subsystem           [v4l2]
 │      39. ov02c10                             [libcamera]
 ├─ Sinks:
 │
 ├─ Sources:
 │  *   53. Built-in Front Camera
...
```

Notice `libcamera` entry. This means pipewire recognized the camera, and it can be now used. You may skip to `Userland support` section.

Otheriwse, if `qcam` is working, but pipewire does not detect it, you need to build libcamera and pipewire from source. It was reported that everything worked out of the box on Arch, but required below manual steps on Ubuntu Concept 25.04.

### Build & Install libcamera

First, remove currently installed `libcamera` (if any), to prevent conflicts:
```bash
sudo apt remove libcamera-dev libcamera0.4 libcamera-tools
sudo apt purge libcamera-dev libcamera0.4 libcamera-tools
sudo apt autoremove
```

Install dependencies for the local build:
```bash
sudo apt install git qt6-base-dev qt6-base-dev-tools libqt6opengl6-dev libjpeg-dev python3-jinja2
```
Clone & build:
```bash
git clone https://git.libcamera.org/libcamera/libcamera.git
cd libcamera

rm -rf build
meson setup build --prefix=/usr -Dpipelines=all -Dqcam=enabled
ninja -C build
```

Install:
```bash
sudo ninja -C build install
sudo ldconfig
```

Running `qcam` will now show a new version in the window title (0.5.1 as of today).

### Build & Install Pipewire

Install dependencies for the local build:
```bash
sudo apt install git libboost-filesystem1.83.0  libboost-log1.83.0  liblttng-ust-common1t64  liblttng-ust-ctl5t64  liblttng-ust1t64  libpisp-common  libpisp1 libdbus-glib-1-dev libv4l-dev libudev-dev libjpeg-dev libepoxy-dev
```

Clone & build. It appears pipewire it tightly tied to the desktop environemnt (at least on Ubuntu), and attempt to remove it breaks things. Do not remove local installation, but do a dirty install of local binaries on top. Because of this, make to sure to _not_ use the latest version, but the same version as installed on your host (eg. for Ubuntu Concept 25.04 its `1.2.7` as of today):

```bash
# IMPORTANT: Make sure to checkout same tag as currently installed on your host
git clone https://gitlab.freedesktop.org/pipewire/pipewire.git -b 1.2.7
cd pipewire

rm -rf build
meson build/ --prefix=/usr --buildtype=release -Dv4l2=enabled -Dlibcamera=enabled
ninja -C build/
```

Install:
```bash
sudo ninja -C build/ install
sudo ldconfig
```

### Userland support

Once installed everything, reboot, or otherwise restart required services:
```
systemctl --user restart pipewire pipewire-pulse wireplumber
```

Generic apps like Gnome's 'Camera' should now work.

#### Firefox support
In firefox navigate to "about:config" and look for the option 'media.webrtc.camera.allow-pipewire', set it to 'True', restart the browser (all windows).

linux-x1e80100-zenbook-a14

linux-x1e80100-zenbook-a14 Latest Version Download

Today's picks

Was this content helpful?

Recent Feedback

linux-x1e80100-zenbook-a14

linux-x1e80100-zenbook-a14 Latest Version Download

Today's picks

Was this content helpful?

Recent Feedback

Download README