vmra1n

KO | EN

gitlite — search

#python #typescript #llm #android #deep-learning #linux #docker #windows #awesome #kubernetes #vue #security #mcp #openai

(★ 66)

Guide on setting up checkra1n in QEMU.

vmra1n 최신버젼 다운로드

최종 버전 다운로드 (.zip)

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

Checkra1n on KVM + QEMU
=======================

You will need:
- Board with support for AMD-V or VT-x, as well as iommu (VT-d)
- Linux distro with QEMU 3.x or higher

You do not need any additional hardware, unless you don't have USB 2.0 ports or separate on-board controllers.

## Enable BIOS Features
Boot into your firmware settings, and turn on AMD-V/VT-x, as well as iommu (also called AMD-Vi, VT-d, or SR-IOV).

## Enable Kernel Features
The `iommu` kernel module is not enabled by default, but you can enable it on boot by passing the following flags to the kernel.

### AMD
```
iommu=pt amd_iommu=on
```

### Intel
```
iommu=pt intel_iommu=on
```

To do this permanently, you can add it to your bootloader. If you're using GRUB, for example, edit `/etc/default/grub` and add the previous lines to the `GRUB_CMDLINE_LINUX_DEFAULT` section, then run `sudo update-grub` (or `sudo grub-mkconfig` on some systems) and reboot.

## Get Some Information
Run `./lsiommu.sh` (included in this repo). If successful, you'll get list of PCIe devices and their IOMMU groups. If there is no output, double check BIOS settings. As an example:
```
IOMMU Group 14 03:00.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] 300 Series Chipset USB 3.1 xHCI Controller [1022:43bb] (rev 02)
IOMMU Group 14 03:00.1 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD] 300 Series Chipset SATA Controller [1022:43b7] (rev 02)
IOMMU Group 18 27:00.3 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] Zeppelin USB 3.0 Host controller [1022:145f]
```
Some groups contain more than one device. Look for an USB controller in its own group, and note the BDF ID (`27:00.3` in this example) and the PCI ID (`1022:145f` in this example).

## Isolate the Controller
Edit `rebind.sh` and change the values for PID and BDF with your own, then save it and run it as `sudo ./rebind.sh`. This will turn off a group of USB ports, so relocate any input devices to other ports as needed. As an example of the format:
```
BIND_PID1="1022 145f"
BIND_BDF1="0000:27:00.3"
```

## Install macOS
Follow https://github.com/foxlet/macOS-Simple-KVM up to step 2. Once installation is finished, shut down the VM.

> Note! The VM's display may go to sleep during installation, which will appear frozen. Simply click on the window and press a key to wake it up.

## Attach USB Controller
Add the following to the end of `basic.sh`, replace `host=XX:XX.X` with the BDF ID from earlier.

```
    -device pcie-root-port,bus=pcie.0,multifunction=on,port=1,chassis=1,id=port.1 \
    -device vfio-pci,host=XX:XX.X,bus=port.1 \
```

## Run Checkra1n
Run `sudo ./basic.sh`. You should be able to connect an iPhone to the assigned ports and run the exploit inside the VM.

# Troubleshooting
```
Please ensure all devices within the iommu_group are bound to their vfio bus driver.
```
The USB controller you selected is in a group with more than one device, either run `rebind.sh` on the other devices with the same group number, or use an ACS patch (for advanced users). You do not need to attach the devices to the VM, only rebind them.

```
iommu doesn't work properly when enabled in BIOS
```
Update your BIOS if possible, older boards may have issues with early implementations.

vmra1n

vmra1n 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

vmra1n

vmra1n 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

Download README