esphome_components

KO | EN

gitlite — search

#ai #go #android #machine-learning #rust #linux #nodejs #macos #windows #cli #kubernetes #vue #pytorch #ios

esphome_components

(★ 40)

ESPHome custom_components

esphome_components 최신버젼 다운로드

최종 버전 다운로드 (.zip)

// repository documentation

Was this content helpful?

★ 0 (0 ratings)

## ESPHome custom components

My creation of custom components fro ESP home.

Please change to WavinAHC9000v3 components as its the most robust version.

### Instructions
Pick the component you want and follow the README in that folder.

📦 **Component index**

- 🛁 **Balboa SPA**: [components/balboa_spa](components/balboa_spa)
- 🌬️ **Genvex v1** (legacy / deprecated): [components/genvex](components/genvex)
- 🌬️ **Genvex v2** ⭐ (recommended): [components/genvexv2](components/genvexv2)
- 🏠 **Wavin Sentio**: [components/sentio](components/sentio)
- 🔥 **Wavin AHC 9000 v1** (legacy / deprecated): [components/wavinAhc9000](components/wavinAhc9000)
- 🔥 **Wavin AHC 9000 v2**: [components/wavinahc9000v2](components/wavinahc9000v2)
- 🔥 **Wavin AHC 9000 v3** ⭐ (recommended): [components/wavinahc9000v3](components/wavinahc9000v3)

## Recent updates
26-01-2026
Added WavinAHC9000v3 component back into this repo
Added Balboa Spa component
Moved instructions for components to respective components folder.

There may be breaking changes, so please make a copy of your current yaml before updating.

05-07-2025 - Updated for ESPHome 2025.6.5+ Compatibility
A big thanks to ricobach for the PR on this.

23-10-2023 - BREAKING CHANGE!!!
Added the ability to use substitutions for channel offset/alignment

The following lines needs to be added to yaml.
```yaml
  # CHANNEL Alignments (ONLY change if you have offsets in channel vs temperature. Some have reported this if using multiple strings pr. room thermostat)
  channel_01_sensor: "0x00"
  channel_02_sensor: "0x01"
  channel_03_sensor: "0x02"
  channel_04_sensor: "0x03"
  channel_05_sensor: "0x04"
  channel_06_sensor: "0x05"
  channel_07_sensor: "0x06"
  channel_08_sensor: "0x07"
  channel_09_sensor: "0x08"
  channel_10_sensor: "0x09"
  channel_11_sensor: "0x0A"
  channel_12_sensor: "0x0B"
  channel_13_sensor: "0x0C"
  channel_14_sensor: "0x0D"
  channel_15_sensor: "0x0E"
  channel_16_sensor: "0x0F"

channel_01: "0x00"
  channel_02: "0x01"
  channel_03: "0x02"
  channel_04: "0x03"
  channel_05: "0x04"
  channel_06: "0x05"
  channel_07: "0x06"
  channel_08: "0x07"
  channel_09: "0x08"
  channel_10: "0x09"
  channel_11: "0x0A"
  channel_12: "0x0B"
  channel_13: "0x0C"
  channel_14: "0x0D"
  channel_15: "0x0E"
  channel_16: "0x0F"
```
  
04-07-2022 - Wavin v2 has issues with ESPhome 2022.6. It fails writing a number back to the Wavin device. Added yaml to basic.yaml to ensure it uses the modbus and modbus_controller component from ESPhome 2022.5.1. Please to a clean and update your ESPhome device to make it work with ESPhome 2022.6.

23-03-2022 - Wavin Sentio - Added support for Wavin Sentio. nic6911 https://github.com/nic6911 have worked hard on a Wavin Sentio component and it has now beed added to this repo.
23-03-2022 - WavinAhc9000v2 - BREAKING CHANGE!!! Add the basic.yaml to the list of packages, see example below. Added support for comfort temperature (seperate climate entity). Added mode action to reflect the current output state of the channel. Idle = not heating, Heat = Heating
23-03-2022 - Genvexv2 - Changed current temp from T1 to T7 as T1 drops when bypass is open. Changed climate entity to .1 decimals.

21-03-2022 - WavinAhc9000v2 - A big thanks to nic6911 https://github.com/nic6911 for testing the comfort temperature config file and providing config files for confort for all the channels

18-03-2022 - WavinAhc9000v2 - Added a file for comfort temperature for channel 1. Only for testing. HAVENT TESTED MY SELF AS I DONT HAVE A THERMOSTAT WITH IR. Please report back if working or not.

16-03-2022 - WavinAhc9000v2 - Inspired by Jopand's work on the nilan custom component I have created an updated version for Wavin Ahc 9000, utilizing the esphome modbus_controller and alot of esphome lambda (Thank you for not using standard modbus function Wavin!).

02-03-2022 - Genvexv2 - Inspired by Jopand's work on the nilan custom component I have created an updated version for Genvex, utilizing the esphome modbus_controller.

## Legacy
Follow the instructions below for the old genvex and wavin components
Add this repository to your ESPHome config yaml:

```yaml
external_components:
  - source: github://heinekmadsen/esphome_components
```

### Example yaml
```yaml
uart:
  rx_pin: GPIO16
  tx_pin: GPIO17
  parity: EVEN
  baud_rate: 19200
  id: uart_modbus
  stop_bits: 1

external_components:
  - source: github://heinekmadsen/esphome_components
    refresh: 0s
    
modbus:
  uart_id: uart_modbus
 
genvex:
  address: 1
  update_interval: 60s
 
sensor:
  - platform: genvex
    temp_t1:
      name: "genvex_temp_t1"
      id: genvex_temp_t1
    target_temp:
      name: "genvex_target_temp"
    speed_mode:
      name: "genvex_speed_mode"

climate:
  - platform: genvex
    name: genvex
    sensor: genvex_temp_t1
```

### Example yaml for PCB to handle both Wavin and Genvex from one ESP.
Reach out to dyrvigk for furter info on PCB
https://github.com/dyrvigk
```yaml
esphome:
  name: genvex-wavin
  platform: ESP32
  board: esp32dev

# Enable logging
logger:
#  level: VERY_VERBOSE

# Enable Home Assistant API
api:

ota:
  - platform: esphome
 
ethernet:
  type: LAN8720
  mdc_pin: GPIO23
  mdio_pin: GPIO18
  clk_mode: GPIO0_IN
  phy_addr: 1
  power_pin: GPIO14
  
status_led:
  pin: GPIO15

output:
  - platform: ledc
    pin: GPIO2
    id: gpio_2
    
    
# Example usage in a light
light:
  - platform: monochromatic
    output: gpio_2
    name: "network Light"
    
interval:
  - interval: 1s
    then:
      if:
        condition:
          api.connected 
        then:
          - output.turn_on: gpio_2
          - output.ledc.set_frequency:
              id: gpio_2
              frequency: "1000Hz"
          - output.set_level:
              id: gpio_2
              level: "10%"    
        else:
          - output.turn_off: gpio_2

external_components:
  - source: github://heinekmadsen/esphome_components
    refresh: 0s

uart:
  - id: uart_1
    rx_pin: GPIO4
    tx_pin: GPIO5
    baud_rate: 38400
    stop_bits: 1
  - id: uart_2
    rx_pin: GPIO16
    tx_pin: GPIO17
    parity: EVEN
    baud_rate: 19200
    stop_bits: 1
    
modbus:
    - id: mod1
      uart_id: uart_1
    - id: mod2
      uart_id: uart_2

# Wavin
wavinAhc9000:
  modbus_id: mod1
  update_interval: 120s
  rw_pin: 33

climate:
  - platform: wavinAhc9000
    channel: 1
    name: "Channel 1"
    visual:
      temperature_step: 0.5 °C
    battery_level:
      name: "Channel 1 Battery"
      state_class: "measurement"
    current_temp:
      name: "Channel 1 Temp"
      state_class: ""
  - platform: wavinAhc9000
    channel: 2
    name: "Channel 2"
    visual:
      temperature_step: 0.5 °C
    battery_level:
      name: "Channel 2 Battery"
    current_temp:
      name: "Channel 2 Temp"
      
  - platform: genvex
    name: genvex
    sensor: genvex_temp_t1

# Genvex
genvex:
  modbus_id: mod2
  address: 1
  update_interval: 60s
 
sensor:
  - platform: genvex
    temp_t1:
      name: "genvex_temp_t1"
      id: genvex_temp_t1
    temp_t3:
      name: "genvex_temp_t3"
    temp_t4:
      name: "genvex_temp_t4"
    temp_t7:
      name: "genvex_temp_t7"
    temp_t2_panel:
      name: "genvex_temp_t2_panel"
    measured_humidity:
      name: "genvex_measured_humidity"
    humidity_calculated_setpoint:
      name: "genvex_humidity_calculated_setpoint"
    alarm_bit:
      name: "genvex_alarm_bit"
    inlet_fan:
      name: "genvex_inlet_fan"
    extract_fan:
      name: "genvex_extract_fan"
    bypass:
      name: "genvex_bypass"
    watervalve:
      name: "genvex_watervalve"
    humidity_fan_control:
      name: "genvex_humidity_fan_control"
    bypass_on_off:
      name: "genvex_bypass_on_off"
    target_temp:
      name: "genvex_target_temp"
    speed_mode:
      name: "genvex_speed_mode"
    heat:
      name: "genvex_heat"
    timer:
      name: "genvex_timer"
      
binary_sensor:
  - platform: status
    name: "Genvex Wavin Controller Status"
```

esphome_components

esphome_components 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

esphome_components

esphome_components 최신버젼 다운로드

오늘의 추천 프로젝트

Was this content helpful?

Recent Feedback

Download README